manualshive.com logo in svg

Fisher & Paykel RS6121VL2K1, Руководство по установке

Поделиться
Скачать
Fisher & Paykel RS6121VL2K1 Скачать руководство пользователя страница 38

38

Slide trim in behind low

er hinge, then t

op hinge

Slot trim in behind hinge pocket, then pr

ess adhesiv

e to ca

vity

ensuring trim is also tight against fridge inner f

ace.

Install parts

Cabinet side trim 
assembly 
(2)

Dual-lock strip  
(4)

Tools

Cross-head screwdriver

Cutter

INSTALL CABINET TRIMS

Installing side trims

Four (4) dual-lock strips are pre-installed along each side trim.

IMPORTANT! 

 

z

Press firmly on the dual-lock strip 

locations to ensure the side trims are 

securely attached. 

 

z

Repeat steps 1-4 to the other side trim. 

Slide trim behind lower hinge, then top hinge. Hold the same 
angle when sliding the trim. 

side trim

top hinge

lower hinge

3

Slide trim in behind low

er hinge, then t

op hinge

Slot trim in behind hinge pocket, then pr

ess adhesiv

e to ca

vity

ensuring trim is also tight against fridge inner f

ace.

Slot trim in behind top hinge pocket, then press 
adhesive to cavity ensuring trim is also tight against 
appliance inner face.

4

Position the trim on the throat at an angle.

2

door hinge

trim

Peel off the liners from 
the dual-lock strips.

1

dual lock strips

Содержание RS6121VL2K1

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды