manualshive.com logo in svg

Fisher & Paykel RS6121VL2K1, Руководство по установке

Поделиться
Скачать
Fisher & Paykel RS6121VL2K1 Скачать руководство пользователя страница 30

30

Door handle kit

M5 x 25

Pan Head

Socket S

cr

ew

OR 

M5x25 he

x scr

ew

M5 x 25

Pan Head

Socket S

cr

ew

OR 

M5x25 he

x scr

ew

M5x25 Hex screw  
(4x)

Door panel 

attachment kit

Side bracket  
(6)

Bracket slider  
(6)

Bracket spacer 
(6)

M5 x 14

M

ush Head

SS  

Philips S

cr

ew

M5 x 14

M

ush Head

SS  

Philips S

cr

ew

8Gx16 Mush washer 
screw (30)

Tools

Cross-head screwdriver

PREPARE FOR DOOR PANEL INSTALLATION

Attaching door handle

Attaching hanging bracket 

and side brackets

Fix hanging bracket to door panel screw 
holes with M5x25 hex screws.

Fix bracket spacer, side bracket and bracket 
slider (in order as per drawing) to screw 
holes on right and left sides of door panel 
with 8Gx16 mush washer screws.

hanging bracket

3

bracket spacer

side bracket

bracket slider

4

IMPORTANT!

 

z

A stainless steel door panel has pre-drilled screw holes for attaching door handle and brackets. 

 

z

For custom door panels, see 'Custom door panel dimensions' (page 15) for correct screw hole 

locations of handles and brackets.

 

z

Remove the protective film around the handle attachment area of the stainless steel panel before 

installing the handle. 

Fix handle to door holes with 
M5x25 hex screws.

1

Remove the blue tape attached 
to inner surface edges of stainless 
steel door panel after the handle is 
installed.

2

door panel 
inner surface

blue tape

blue tape

Содержание RS6121VL2K1

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды