manualshive.com logo in svg

Fisher & Paykel RS6121VL2K1, Руководство по установке

Поделиться
Скачать
Fisher & Paykel RS6121VL2K1 Скачать руководство пользователя страница 21

21

Back wall

alcove return

Floor

PROFILE VIEW

INSTALL ANTI-TIP BRACKET

Anti-tip bracket 

assembly kit

Anti-tip bracket  
(1)

Masonry plug  
(4)

#10x40

Pan Head

Philips S

cr

ew

#10x40

Pan Head

Philips S

cr

ew

#10x40 cross-head 
screw (4)

Tools

Cross-head screwdriver

Powered drill

Pencil

Leveler

Safety glasses

screws

For plaster board wall installation

Fix bracket to wall with 10x40mm cross 
head screws (4x), and screw tightly with 
a screwdriver. 

5

For solid wall installation

Hammer 10x30mm masonry plugs into wall until 
flush. Fix bracket to wall with 10x40mm cross head 
screws (4x), and screw tightly. 

6

IMPORTANT!

Ensure the bracket overlaps the appliance by a minimum 7 1/16" (min 180mm) for a secure hold. If the minimum 

7 1/16" (180mm) overlap cannot be achieved, install a solid spacer to the wall screw behind the bracket.

min 180mm

Bracket

Appliance

Back wall

Bracket

Spacer

Appliance

Back wall

min 180mm

Mark a horizontal line on the back wall 
based on measured attachment height. 
Ensure there is a stud behind the wall.

2

Mark screw hole locations, and drill 
screw holes with powered drill. 

4

Place the bracket to the backwall. 
Align the undersurface of bracket 
along the marked line.

3

stud

Measure height from floor to alcove return (

A

). Use this 

measurement to locate the attachment height (

B

) of 

anti-tip bracket to the back wall.

 

z

Attachment height of anti-tip bracket should not 
be more than 2138mm to ensure the appliance is 
prevented from tipping over during installation. 

1

B

A

min 197mm

bracket

masonry plugs

Содержание RS6121VL2K1

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды