manualshive.com logo in svg

Fisher & Paykel RS6121VL2K1, Руководство по установке

Поделиться
Скачать
Fisher & Paykel RS6121VL2K1 Скачать руководство пользователя страница 20

20

Check the installation location

Check the cabinetry

 

z

Check the dimensions of the cabinetry: height, width, depth, floor level, finished 
alcove returns.

Check the power supply connection

 

z

Ensure that there is a separate power socket for each appliance. 

 

z

Avoid sharing the power point with other appliances to prevent accidental switching off 
of the appliance.

 

z

For power requirements, refer to the information on the serial plate. 

 

z

Ensure your appliance is properly grounded (earthed).

 

z

Connect your appliance to an electrical supply with the fitted plug and lead.

 

z

If power connection is located behind the appliance, we recommend to install an isolating 
switch to a location that is easily accessible to the user for repair or disconnection. 

 

z

Follow local codes and ordinances when installing the appliance.

BEFORE INSTALLATION

Содержание RS6121VL2K1

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды