Fisher & Paykel RS6121VL2K1 Скачать руководство пользователя страница 19

Страница: 19 / 48

BEFORE INSTALLATION

Follow the steps below to move your appliance to installation location. Be careful when tilting the appliance forward/backward.

Remove external box.

Move your appliance

Check your appliance

Remove brackets from one side of pallet.

Tilt slightly forward and Insert hand truck.

Hand truck

Restrain with strap and remove remaining brackets.

Strap

Tilt backward to load appliance onto hand truck.

IMPORTANT!

Ensure that your appliance is the

correct model as per your order.

Check that the components and

install kits are complete.

Keep the detached parts to

reinstall later.

air flow divider

top door panel extrusion

top trim

toe kick mounting plate

top grille

bottom grille

Installation kit

Air flow divider

INTE

GRA

TED

COL

UMNS

RS462

1F, RS

6121F

, RS7

621F,

RS6121

S & RS7

621S

models

INS

TALLA

TION

GUIDE

NZ A

U GB

84916

10.18

Miscellaneous items

(MI) pack

Top door panel

extrusion

Top grille

Top trim

Bottom grille

Toe kick mounting plate

Remove installation kit, MI pack and pre-installed parts.
Keep all components to use later.

Содержание RS6121VL2K1

















































Результаты поиска

Содержание RS6121VL2K1

Отзывы:

Бренды по названию

Популярные бренды

Fisher & Paykel RS6121VL2K1, Руководство по установке

Результаты поиска

Содержание RS6121VL2K1

Отзывы:

Бренды по названию

Популярные бренды