manualshive.com logo in svg

Fisher & Paykel RS6121VL2K1, Руководство по установке

Поделиться
Скачать
Fisher & Paykel RS6121VL2K1 Скачать руководство пользователя страница 14

14

TOE KICK PANEL DIMENSIONS

E

F

Standard toe kick height is 102mm with 

Stainless steel door panel

50mm toe kick height*  

(with extra lower grille attached)

73 – 102mm toe kick depth measured 

from from rear of door panel

152mm toe kick height**

A

B

C

TOE KICK DIMENSIONS

MM

A

Width of toe kick

Stainless steel panel/Custom panel

607

B

Height of toe kick

#

Stainless steel panel

102

Custom panel**

50 – 152

C

Depth of toe kick 

(measured from front of door)

Stainless steel panel/Custom panel

73 –102

#

   Standard toe kick height is 4" (102mm) with the optional Stainless door panel. For Custom door panel installation, a custom toe kick 2 – 6" (50 – 152mm) can be 

manufactured and fitted by cabinetmaker. The Custom door panel height needs to be adjusted accordingly.

** Extra bottom  grilles are required for a 2" (50mm) toe kick installation. You can purchase the extra bottom grille (Part No. 847542P) online at fisherpaykel.com.

Содержание RS6121VL2K1

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды