1
2
3
4
5
6
RECOMMENDED PLACEMENT FOR
HEARING IMPAIRED STROBE LIGHT
According to NFPA 72, at a minimum a strobe should be
installed within 16 feet (4.9 meters) of the pillow.
For wall mounting: The strobe should be between 80
to 96 inches (203 to 244 cm) above the floor.
For ceiling mounting: Ideally the strobe should be located
near the center of the room. See diagram.
This strobe light must be interconnected with smoke,
heat and/or carbon monoxide alarms either within or
nearby the sleeping rooms to provide protection.
STROBE LIGHT OUTPUT FOR WALL & CEILING MOUNTING
The intensity of the strobe light gradually lessens as the angle
increases. In other words, the light is brightest directly in front
of the strobe light and is progressively less bright to either side.
As required by Underwriters Laboratories, Inc. (UL), the following
illustrations show how the strobe light is dispersed. Use them to
help you choose where to locate units for the hearing impaired.
90
90
Angle
(In Degrees)
Percent
Light Intensity
0
5-25
30-45
50
55
60
65
70
75
80
85
90
100
90
75
55
45
40
35
35
30
30
25
25
45
45
0
90
90
45
45
0
WALL
LIGHT
LIGHT
CEILING
FIGURE 1: Light Output
for Ceiling Mount
FIGURE 2: Light Output
for Wall Mount
PHOTOSENSITIVE EPILEPSY AND STROBE FLASH RATES
Individuals who are susceptible to photosensitive epilepsy
might have an increased probability for seizures with multiple
strobe lights flashing asynchronously. The frequency or speed
of flashing light that is most likely to cause seizures varies from
person to person. Generally, flashing lights most likely to trigger
seizures are between the frequency of 5 to 30 flashes per second
(Hertz). This strobe light flashes at about 1 flash per second.
Under the Americans with Disabilities Act, most workplaces
and places serving the public, including theaters, restaurants,
and recreation areas, are required to have fire alarms, which
flash as well as ring so that people who cannot hear or
cannot hear well will know that there is an emergency.
This strobe LED syncs with other family units.
WEEKLY TESTING
To test this strobe light you must activate the test button of each
interconnected, smoke, CO or heat alarm. This will send a signal to the
strobe light and cause the unit to begin flashing. Depending on what type
of alarms you have connected, the strobe light will flash different patterns.
Smoke/Heat Alarms:
Constant approximately 1 flash per second.
CO Alarms:
Intermittent approximately 1 flash per second for
four flashes, then 5 seconds off. Pattern is repeated.
These different patterns are to help a hearing impaired person better
distinguish the danger present. The flash patterns approximate the audible
alarm emitted by either a smoke or heat alarm or a carbon monoxide alarm.
Note that a heat alarm will emit the same horn pattern as a smoke alarm.
Make sure all members of your family understand the different flash patterns.
Do not look directly at or touch the lens while the strobe light
is flashing. Doing so can hurt your eyes or burn your fingers.
If
the strobe light does not flash during testing and the alarm does not
sound, check the fuse or circuit breaker supplying power to the alarm
circuit. If the alarm sounds and the strobe light does not flash, refer to
the installation instructions in this manual to insure strobe light is wired
properly. If the strobe light still does not work it should be replaced.
When testing the interconnected alarm, do not stand too
close to the unit when the alarm is sounding. It is loud to wake
you in an emergency. Exposure to the horn at close range
may harm your hearing.
All interconnected alarms connected
to this strobe light must be tested individually to ensure proper
connections. It is important to test all interconnected alarms every
week to make sure they are working properly. Using the test button
is the recommended way to test the alarms and strobe light.
HOW TO INSTALL THIS STROBE LIGHT
This Strobe Light is designed to be mounted on any standard wiring junction box to a 4-inch (10 cm) diagonal size, on either the ceiling
or wall (if allowed by local codes). Read “Recommended Placement for Hearing Impaired Lights” before you begin installation.
Tools you will need: • Standard Flathead screwdriver • wire strippers
THE PARTS OF THIS STROBE LIGHT
The Mounting Bracket:
To remove the mounting bracket from the Strobe
Light base, hold the Strobe Light base firmly and
twist the mounting bracket counterclockwise. The
mounting bracket installs onto the junction box.
It has a variety of screw slots to fit most boxes.
The Power Connector:
The power connector plugs into a
power input block on the Strobe Light.
It supplies the unit with AC power.
•
The black wire is “hot.”
•
The white wire is neutral.
•
The orange wire is used for interconnect.
If you need to remove the power connector, turn
POWER OFF first.
Insert a flat screwdriver blade
between the power connector and the security tab
inside the power input block. Gently pry back the
tab and pull the connector free.
4
3
5
7
8
6
The Parts of This Unit
1.
Mounting Bracket
2.
Mounting Slots
3.
Hot (Black) AC Wire
4.
Neutral (White) AC Wire
5.
Interconnect
(Orange) Wire
6.
Quick-Connect
Power Connector
7.
Turn this way to
remove from bracket
(Counterclockwise)
8.
Turn this way to attach
to bracket (Clockwise
Make sure the Alarm is not receiving excessively noisy power. Examples of noisy power could be
major appliances on the same circuit, power from a generator or solar power, light dimmer on the same circuit
or mounted near fluorescent lighting. Excessively noisy power may cause damage to your Alarm.
FOLLOW THESE INSTALLATION STEPS
The basic installation of this strobe light is similar whether you
want to install one strobe light or multiple strobe lights.
This device is not a smoke, heat or CO alarm. It must
be interconnected with operating alarms to provide
protection. It will not work without AC power.
Things to consider when planning the installation
of a hearing impaired strobe light:
•
Location of strobe light is important and must comply with
NFPA 72 requirements. This device is intended o awaken a
hearing impaired person and must be positioned properly for it
to be effective. See Installation Diagram and “Recommended
Locations for Hearing Impaired Strobe Lights” for details.
•
Types of other alarms to be interconnected with this strobe light. This
device can be interconnected with smoke, heat, carbon monoxide
alarms or a combination of all three. A smoke alarm is usually placed
within the sleeping area. Follow recommendations in each device’s
installation manual. The interconnect wire of all alarms must be
properly connected for the strobe light to be operational. The strobe
light may be positioned anywhere within the interconnected circuit.
ELECTRICAL SHOCK HAZARD. Turn off
power before starting installation!
1.
Remove the mounting bracket from the base. Install
the mounting bracket to the junction box.
2.
Using wire nuts, connect the power connector to the household wiring
as follows:
Strip off about 1/2” (12mm) of the plastic coating on
the orange wire on the power connector.
•
Connect the white wire on the power connector
to the neutral wire in the junction box.
•
Connect the black wire on the power connector
to the hot wire in the junction box.
•
Connect the orange wire on the power connector to the
interconnect wire in the junction box. Repeat for each unit
you are interconnecting. Never connect the hot or neutral
wires in the junction box to the orange interconnect wire.
3.
Plug the power connector into the back of the Strobe Light.
4.
Line up the alignment tab on the base with the alignment tab
on the mounting bracket. Turn the Strobe Light clockwise
(right) until you hear the unit snap into place
.
5.
Check all connections.
Improper wiring of the power connector or the wiring leading to the power connector
will cause damage to the Strobe Light and may lead to a non-functioning unit.
• If you are installing multiple Strobe Lights, repeat steps 1-5 for each Strobe
Light in the series. When you are finished, restore power to the junction box.
ELECTRICAL SHOCK HAZARD! Do not restore power until all devices
are completely installed. Restoring power before installation is
complete may result in serious electrical shock, injury or death.
6.
Make sure the Strobe Light is receiving AC power. Under normal
operation, the green power indicator light will shine continuously. If
the power indicator light does not light, TURN OFF POWER TO THE
JUNCTION BOX and recheck all connections. If all connections are
correct and the power indicator still does not light when you restore the
power, the unit should be replaced immediately.
7.
To test this strobe light you must activate the test button of each
interconnected, smoke, CO or heat alarm. This will send a signal to the strobe
light and cause the unit to begin flashing. Depending on what type of alarms
you have connected, the strobe light will flash different patterns.
Smoke/Heat Alarms: Constant approximately 1 flash per second.
CO Alarms: Intermittent approximately 1 flash per second for four flashes, then
5 seconds off. Pattern is repeated.
These different patterns are to help hearing impaired person better
distinguish the danger present. The flash patterns approximate the audible
alarm emitted by either a smoke/heat alarm or carbon monoxide alarm.
Do not look directly at or touch the lens while the strobe light is flashing.
If any Strobe Light does not flash, TURN OFF POWER and
recheck connections. If any Strobe Light still does not flash when
you test it after restoring power, replace it immediately.
This Strobe Light can be interconnected with all current model hardwired
First Alert
®
and
BRK Electronics
®
branded Smoke Alarms, Carbon
Monoxide Alarms, Combination Smoke/CO Alarms, Heat Alarms
and relays. Call First Alert Consumer Affairs at 1-800-323-9005.
Interconnected units with a single family residence only, otherwise
all households will experience unwanted alarms when you test
any unit in the series. Interconnected units will only work if they
wired to compatible units and all requirements are met.
Interconnected units must meet ALL of the following requirements:
•
A maximum of 18 units of total may be interconnected
(Maximum of 12 Smoke Alarms).
•
The same fuse or circuit breaker must power all interconnected Alarms.
•
The total length of wire interconnecting the units should be
less than 1000 feet (305 meters). This type of wire is commonly
available at Hardware and Electrical Supply stores.
•
All wiring must conform to all local electrical codes and NFPA 70
(National Electrical Code), Refer to NFPA 72, NFPA 101, and/or your
local building code for further connection requirements.
5
}
A
}
B
8
7
6
3
1
1
2
2
3
4
4
5
A.
120VAC 60 Hz source
B.
To additional units; Maximum = 18
total (Maximum 12 Smoke Alarms)
1.
Strobe Light
2.
Ceiling or Wall
3.
Power Connector
4.
Wire Nut
5.
Junction Box
6.
Neutral Wire (Wht)
7.
Interconnect
Wire (Orange)
8.
Hot Wire (Blk)
REGULAR MAINTENANCE
This unit has been designed to be as maintenance-free as possible, but
there are a few simple things you must do to keep it working properly.
•
Test it at least once a week.
•
Clean the Strobe Light at least once a month; gently vacuum off
any dust using your household vacuum’s soft brush attachment,
and test the Strobe Light after cleaning. Never use water,
cleaners or solvents since they may damage the unit.
• If the strobe light lens is loose or broken, the entire unit
should be replaced immediately. Never remove the Strobe
Light lens for any reason. Doing so can permanently
damage the unit and will void your warranty.
• Do not paint over the unit. Paint may clog the openings
and prevent the unit from operating property.
IF THIS STROBE LIGHT ACTIVATES
RESPONDING TO AN ALARM
During an alarm, depending on what type of alarms you have
connected, the strobe light will flash different patterns.
Smoke/Heat Alarms: Constant approximately 1 flash per second.
CO Alarms: Intermittent approximately 1 flash per second for four
flashes, then 5 seconds off. Pattern is repeated.
End of Life: 5 Green LED flashes once per minute
These different patterns are to help a hearing impaired
person better distinguish the danger present. The flash
patterns approximate the audible alarm emitted by either
a smoke/heat alarm or carbon monoxide alarm.
The appropriate smoke, CO or heat alarm will also be sounding
their repeating horn patterns: Smoke or Heat Alarm you will
hear 3 beeps, pause, 3 beeps, pause. Carbon Monoxide danger
you will hear 4 fast beeps, pause, 4 fast beeps, pause.
IF AN INTERCONNECTED CO ALARM SOUNDS
“ALARM - MOVE TO FRESH AIR”
If you hear an interconnected CO alarm horn and the CO red
light is flashing, move everyone to a source of fresh air.
DO NOT remove the batteries.
Actuation of an interconnected CO Alarm indicates the presence
of carbon monoxide (CO) which can kill you. In other words,
when your CO Alarm sounds, you must not ignore it!
IF AN INTERCONNECTED CO ALARM SIGNAL SOUNDS:
1.
Operate the Test/Silence button.
2.
Call your emergency services, fire department or 911.
Write down the number of your local emergency service
here: _____________________________________
3.
Immediately move to fresh air – outdoors or by an open door or window.
Do a head count to check that all persons are accounted for. Do not
re-enter the premises, or move away from the open door or window
until the emergency services responder has arrived, the premises have
been aired out, and your CO Alarm remains in its normal condition.
4.
After following steps 1-3, if your CO Alarm reactivates within a 24-hour
period, repeat steps 1-3 and call a qualified appliance technician to
investigate for sources of CO from fuel-burning equipment and appliances,
and inspect for proper operation of this equipment. If problems are
identified during this inspection have the equipment serviced immediately.
Note any combustion equipment not inspected by the technician, and
consult the manufacturers’ instructions, or contact the manufacturers
directly, for more information about CO safety and this equipment. Make
sure that motor vehicles are not, and have not, been operating in an
attached garage or adjacent to the residence. Write down the number of
qualified appliance technician here:
______________________________________________________
NOTE:
A qualified appliance technician is defined as a “person,
firm, corporation, or company that either in person or through a
representative is engaged in and responsible for the installation, testing,
servicing, or replacement of heating, ventilation, air conditioning
(HVAC) equipment, combustion appliances and equipment, and/
or gas fireplaces or other decorative combustion equipment.”
IF AN INTERCONNECTED SMOKE ALARM SOUNDS
RESPONDING TO AN ALARM
\
• If an interconnected unit alarms and you are not testing the
unit, it is warning you of a potentially dangerous situation
that requires your immediate attention. NEVER ignore any
alarm. Ignoring the alarm may result in injury or death.
• Never remove the batteries from a battery operated Smoke/CO
Alarm to stop an unwanted alarm (caused by cooking smoke, etc.).
Removing batteries disables the alarm so it cannot sense smoke,
and removes your protection. Instead open a window or fan the
smoke away from the unit. The alarm will resent automatically.
• If the unit alarms get everyone out of the immediately.
WHAT TO DO IN CASE OF FIRE
•
Don’t panic; stay clam. Follow your family escape plan.
•
Get out of the house as quickly as possible. Don’t
stop to get dressed or collect anything.
•
Feel doors with the back of your hand before opening them. If a
door is cool, open it slowly. Don’t open a hot door. Keep doors
and windows closed, unless you must escape through them.
•
Cover your nose and mouth with a cloth (preferably
damp). Take short, shallow breaths.
•
Meet at your planned meeting place outside your home, and
do a head count to make sure everybody got out safely.
•
Call the Fire Department as soon as possible from
outside; Give your address, then your name.
•
Never go back inside a burning building for any reason.
•
Contact your Fire Department for ideas on making your home safer.
IF YOU SUSPECT A PROBLEM
If the strobe light lens is loose or broken, the entire unit should be
replaced immediately. Never remove the strobe light lens for any reason.
Doing so can permanently damage the unit and will void your warranty.
Always discharge the branch circuit before servicing an
AC or AC/DC Alarm. First, turn off the AC power at the
circuit breaker or fuse box. Next, remove the battery from
Alarms with battery back-up. Finally, press and hold the test
button for 5-10 seconds to disable the branch circuit.
Do not try fixing the alarm yourself – this will void your warranty!
If the device is still not operating properly, and it is still under warranty,
please see “How to Obtain Warranty Service” in the Limited Warranty.
SPECIAL COMPLIANCE CONSIDERATIONS
Strobe Lights along with residential smoke and carbon monoxide alarms
alone are not suitable substitute for complete fire detection systems in
places housing many people – like apartment buildings, condominiums,
hotels, motels, dormitories, hospitals, long-term health care facilities,
nursing homes, day care facilities, or group homes of any kind – even if
they were once single family homes. They are not a suitable substitute
for complete fire detection systems in warehouses, industrial facilities,
commercial buildings, and special-purpose non-residential buildings
which require special fire detection and alarm systems, typically in only
the sleeping areas. Depending on the building codes in your area, these
devices may be used to provide additional protection in these facilities.
FCC Compliance
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit
different from that of the receiver.
•
Consult the dealer or an experienced radio or TV technician for help.
Changes or modifications to the product, not expressly
approved by First Alert/ BRK Brands, Inc., could void
the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
LIMITATIONS OF STROBES
Strobe and alarms may not waken all individuals.
Practice the escape plan
at least twice a year, making sure that everyone is involved – from kids to
grandparents. Allow children to master fire escape planning and practice
before holding a fire drill at night when they are sleeping. If children or others
do not readily awaken to audible or visual signals, or if there are infants
or family members with mobility limitations, make sure that someone is
assigned to assist them in fire drills and in the event of an emergency. It is
recommended that you hold a fire drill while family members are sleeping
in order to determine their response while sleeping and to determine
whether they may need assistance in the event of an emergency.
The Strobe cannot work without AC power.
The strobe will not
operate if AC power is cut off for any reason (open fuse or
circuit breaker, failure along a power line or at a power station,
electrical fire that burns the electrical wires, etc.).
The Strobe will not operate unless smoke, heat or CO reaches
the corresponding alarm.
Refer to the user’s manuals supplied
with the interconnected smoke, heat or CO alarms.
Strobes may not be seen.
Hearing impaired individuals may not
see the visual notification if obstructions such as doors, walls, or
bright lights block the strobe light. The use of alcohol or drugs
may also impair ones ability to respond to the visual signal.
Strobes are not foolproof.
Like any electronic device, strobes are
made of components that can wear out or fall at any time. You
must test the unit weekly to ensure your continued protection.
Strobes are not a substitute for property or life insurance.
Hearing deficits may not be apparent.
If in doubt, consult your doctor.
Strobes have a limited life.
The unit should be replaced immediately if it is not
operating properly. Replace the strobe 10 years from date of installation.
LIMITED WARRANTY
BRK Brands, Inc., (“BRK”) the maker of First Alert
®
brand and BRK
®
brand
products, warrants that for a period of ten years from the date of purchase,
this product will be free from defects in material and workmanship. BRK,
at its option, will repair or replace this product or any component of the
product found to be defective during the warranty period. Replacement
will be made with a new or remanufactured product or component. If the
product is no longer available, replacement may be made with a similar
product of equal or greater value. This is your exclusive warranty.
This warranty is valid for the original retail purchaser from the date of initial
retail purchase and is not transferable. Keep the original sales receipt.
Proof of purchase is required to obtain warranty performance. BRK dealers,
service centers, or retail stores selling BRK products do not have the right to
alter, modify or any way change the terms and conditions of this warranty.
This warranty does not cover normal wear of parts or damage resulting from
any of the following: negligent use or misuse of the product, use on improper
voltage or current, use contrary to the operating instructions, disassembly,
repair or alteration by anyone other than BRK or an authorized service
center. Further, the warranty does not cover Acts of God, such as fire, flood,
hurricanes and tornadoes or any batteries that are included with this unit.
BRK shall not be liable for any incidental or consequential damages caused
by the breach of any express or implied warranty. Except to the extent
prohibited by applicable law, any implied warranty of merchantability or fitness
for a particular purpose is limited in duration to the duration of the above
warranty. Some states, provinces or jurisdictions do not allow the exclusion
or limitation of incidental or consequential damages or limitations on how
long an implied warranty lasts, so the above limitations or exclusion may
not apply to you. This warranty gives you specific legal rights, and you may
also have other rights that vary from state to state or province to province.
How to Obtain Warranty Service
Service:
If service is required, do not return the product to your retailer.
In order to obtain warranty service, contact the Consumer Affairs
Division at 1-800-323-9005. To assist us in serving you, please have
the model number and date of purchase available when calling.
For Warranty Service return to:
BRK Brands,
Inc., 1301 Joe Battle, El Paso, TX 79936
Visit
www.firstalert.com or www.brkelectronics.com
for more information.
BRK
®
is a registered trademark of BRK Brands, Inc.
First Alert
®
is a registered trademark of the First Alert Trust.
USER’S MANUAL
AC POWERED LED STROBE LIGHT
FOR THE HEARING IMPAIRED
M08-0218-159019
J1
08/17 Printed in Mexico
CONFORMS TO
UL STD 1971
Model SLED177
Input: 120V AC ~, 60Hz
Electrical Rating:
0.8A Alarm
Strobe:
177 candela minimum
IMPORTANT! PLEASE READ CAREFULLY AND SAVE.
This user’s manual contains important information about your Strobe
Light’s operation. If you are installing this Strobe Light for use by others,
you must leave this manual—or a copy of it—with the end user.
© 2017 BRK Brands, Inc. All rights reserved. Distributed by BRK Brands, Inc.
•
BRK Brands, Inc. is a subsidiary of Newell Brands Inc. (NYSE:NWL)
•
First Alert
®
is registered trademark of The First Alert Trust
•
3901 Liberty Street, Aurora,
IL 60504-8122
•
Consumer Affairs: (800) 323-9005 www.firstalert.com
•
www.
brkelectronic.com
INTRODUCTION
Thank you for choosing First Alert
®
for your hearing impaired strobe
light needs. You have purchased a state of the art Strobe Light designed
to provide hearing impaired individuals with a visual warning of a fire
or a carbon monoxide danger when used with smoke, heat or carbon
monoxide alarms. Please take the time to read this manual and make
this Strobe Light an integral part of your family’s safety plan.
Key Features of the SLED177 Strobe Light:
Smart Strobe:
Separate flash patterns to distinguish between
smoke/heat or CO danger. Can be interconnected with First Alert
®
and BRK
®
smoke, CO, smoke/CO combo and heat alarms.
177 Candela LED Light:
Powerful 177 candela LED strobe light provides
effective visual warning to awaken hearing impaired residents.
Strobe Signal Synchronization:
LED syncs with other family units.
1Hz Flash Rate:
60 flashes per minute meets ADA, ANSI 117.1, NFPA
72, and UL 1971 requirements for visual signaling devices.
Smart Interconnect:
One interconnect wire
carries smoke and CO alarm signals.
Meets ADA Requirements:
Meets the requirements
of the Americans with Disabilities Act (ADA).
Alarm Indication:
Automatically identifies which unit initiated alarm.
Low Profile Design:
Mounts easily on ceiling or wall.
This device is not a smoke, heat or carbon monoxide
alarm. It must be interconnected with operating alarms to
provide protection. It will not work without AC power.
BEFORE YOU INSTALL THIS STROBE LIGHT
Read “Recommended Placement for Hearing Impaired Strobe Lights”.
This Strobe Light is intended to be interconnected with functioning smoke,
heat or carbon monoxide alarms. It has no means of detection on its own.
It will not operate without AC power. Its operation is specifically designed
to wake hearing impaired persons as specified by NFPA 72, Underwriters
Laboratories (UL 1971), Americans with Disabilities Act (ADA) and ANSI 117.1.
This Strobe Light can ONLY give an early warning of potentially
dangerous fire or CO Incident if it is installed, maintained and
located where hearing impaired residents can see it, as described
in this manual. This unit will not sense smoke, carbon monoxide,
gas, heat, or flame. It cannot prevent or extinguish fires.
Check Your Local Building Codes
This Strobe Light is designed to be used in a typical residential single-
family or multi-family dwellings and institutional applications including
sleeping areas of hospitals, hotels, motels, nursing homes, long term
health care facilities, day care facilities, dormitories or other similar
dwellings. See “Special Compliance Considerations” for details.
ELECTRICAL SHOCK HAZARD. Turn off the power to the area where
you will install this Strobe Light at the circuit breaker or fuse box
before beginning installation. Failure to turn off the power before
installation may result in serious electrical shock, injury or death.
• Installation of this Strobe Light must conform to the electrical
codes in your area; Articles 210, 760 of NFPA 70 (NEC), NFPA 72,
NFPA 101; SBC (SBCCI); UBC (ICBO); NBC (BOCA); OTFDC (CABO),
and any other local or building codes that may apply. Wiring and
installation must be performed by a licensed electrician. Failure to
follow these guidelines may result in injury or property damage.
• This Strobe Light must be powered by a 24-hour, 120VAC
60Hz circuit. Be sure the circuit cannot be turned off
by a switch, dimmer, or ground fault circuit interrupter.
Failure to connect this Strobe Light to a 24-hour circuit
may prevent it from providing constant protection.
• It is possible an electrical fire could occur on the circuit
powering this Strobe Light. If this happened, power to the
unit could be cut off and it may fail to activate. Some safety
experts recommend wiring warning devices like this unit on
separate circuits from other appliances, since these circuits
are not as likely to be overloaded. Other safety experts
recommend wiring these units on the same circuits as
appliances so it is more readily apparent if the circuit fails.
• Never disconnect the power from an AC powered unit to stop
an unwanted alarm. Doing so will disable the unit and remove
your protection. In the case of a true unwanted alarm open a
window or fan the smoke away from the interconnected units.
The interconnected alarm will reset automatically when it
returns to normal operation. Never remove the batteries from
a battery operated unit to stop an unwanted alarm (caused by
cooking smoke, etc.). Instead open a window or fan the smoke
away from the unit. The alarm will reset automatically.
Printed in Mexico M08-0218-159019
J1
08/17
