background image

 

 

 

 

1

 

 

 

 

DESCRIPTION 

The NXD410TS Touch Screen User Interface provides the means to setup, monitor and display all information 
from the PPC4000 and NXF4000 Control and connected accessories. The NXD410TS is a 4.3” widescreen TFT 
color touchscreen. The NXD410TS is panel mounted and connects directly to the PPC4000 and NXF4000 using 
cable part number 59-561 available by the foot. 

Refer to Bulletin PPC-4001 for a complete description of the PPC4000 control system or for NXF4000 See 
Bulletin NXF-4001. 

SPECIFICATIONS 

 

NXD410TS 

Supply Voltage: 

24 Vdc (18 to 30 Vdc) 

Power 
Consumption: 

0.60A at 24Vdc (max.) 

Temperature Rating: 

32°F to 122°F (0°C to +50°C) 

Protection Category: 

Indoors use only, IP40

 

 

Unit Dimensions: 

Faceplate LxH 129x88 mm 
(5.1“)x(3.45“) 
Cutout AxB 106.5x73.025 mm 
(4.19“)x(2.875“) 
allow 1.725” (43.8mm) depth clearance 

Interface Method

RS485, 57600 Baud 

Shipping Weight: 

Approx. 0.9 lbs. (0.41 Kg) 

 

NOTE

Proper operation of the NXD410TS Touchscreen display requires a PPC4000 with an 

Engineering code of 9 or greater or a PPC4000 running main firmware revision v3.7 or greater. 
Due to limitations of Modbus RTU, only one master can exist on the Modbus interface. The 

NXTSD4xx Touchscreen display is considered the master of the bus and the Modbus 

system should be configured such that the Touchscreen display is the only device speaking 

to the PPC4000(s) on the bus.

 

 

         NXDTS-4410  
December 16, 2019 

NXD410TS

TOUCHSCREEN

INSTALLATION GUIDE

USED WITH PPC4000 and

NXF4000 FUEL AIR RATIO 

CONTROLLER

Содержание NXD410TS









Отзывы: