REPLACING THE BRUSH HEAD SPLASH GUARD
If the splash guard rubber blades of the brush head side casing are damaged they cannot work properly, namely they cannot convey the dirty
detergent solution towards the squeegee, therefore the splash guard rubber blades need to be checked. To replace the brush head splash
guards, proceed as follows:
1. Open the machine's left side casing (7) (
Fig.8
).
2.
Remove the left splash guard body (8) and move the fixing anchors (9) on the brush head body into the maintenance position (
Fig.9
).
3. Remove the rear rubber blade compression plate (10), and release the stopper (11) on rubber blade compression plate (
Fig.10
).
4. Remove the splash guards (12) from the left splash guard body and replace it with a new one or else turn it around (
Fig.11
).
5. Repeat the operations in reverse order to reassemble all the parts.
6. Repeat the operations just carried out also for the right side casing as well.
REPLACING THE SIDE SQUEEGEE SPLASHGUARD RUBBER BLADES
If the splashguard rubber blades of the side squeegee are damaged they cannot work properly, namely they cannot convey the dirty detergent
solution towards the squeegee, therefore the rubber blades need to be checked. To replace the brush head splash guards, proceed as follows:
1. Extract the vacuum hose (1) from the vacuum nozzle on the squeegee body (
Fig.1
).
2. Completely unscrew the knobs (2) in the squeegee body's pre-assembly (
Fig.2
).
3. Remove the squeegee body from the slits in the squeegee connector (
Fig.3
).
4. Using the right equipment (not supplied with the machine) remove the screw (13) (
Fig.12
).
5. Using the right equipment (not supplied with the machine) remove the nut (14) (
Fig.13
).
6. Remove the left side squeegee (15) from the machine (
Fig.14
).
7.
Using the right equipment (not supplied with the machine) remove the splashguard rubber blade fixing screws (16) (
Fig.15
).
8. Remove the old splashguard rubber blades (17) and replace them with new ones (
Fig.16
).
9. Repeat the operations in the reverse order and reassemble all the parts, then move on to the right side squeegee.
N.B.:
remember to put the blade compression plate (18) between one splashguard rubber blade and the other (
Fig.16
).
N.B.:
when adjusting the side squeegee remember to leave about 10 mm of the threaded part beyond the self-locking flanged nut (14)
(
Fig.12
).
FILLING BRAKING SYSTEM OIL BASIN
If a braking system anomaly alarm is activated when you are working, quickly stop the machine and check the oil level in the machine's brake
system.
To check and top up the oil in the braking system, proceed as follows:
1.
Using the right equipment (not supplied with the machine) remove the screws (19) fixing the front fairing to the steering column (
Fig.17
).
2. Using the handles (20), remove the fairing (21) from the machine and lay it on the ground (
Fig.18
).
3. Check the level of oil in the basin (22), if necessary adding fresh oil.
4.
To top up the braking system liquid basin, remove the cap-float (23) (
Fig.19
).
5. Put the brake liquid into the basin, being careful not to add too much.
N.B.:
for the machine's braking system, use "Shell brake fluid dot 4" brake fluid.
CAUTION:
to prevent serious injuries carefully read the product's safety sheet.
N.B.:
The place given over to this operation must comply with current environmental protection regulations.
REPLACING THE SQUEEGEE BODY RUBBER BLADES
Ensuring the integrity of the squeegee body's rubber blades guarantees better floor cleaning and drying results, as well as a longer service life
for the vacuum motor. In order to replace the squeegee body's rubber blades, do the following:
1. Extract the vacuum hose (1) from the vacuum nozzle on the squeegee body (
Fig.1
).
2. Completely unscrew the knobs (2) in the squeegee body's pre-assembly (
Fig.2
).
3. Remove the squeegee body from the slits in the squeegee connector (
Fig.3
).
4. Remove the rear rubber blade compression plate, and release the stopper (3) at the rear of the squeegee (
Fig.4
).
5. Remove the rear rubber blade (4) from the squeegee body (
Fig.5
).
6. Completely unscrew the knobs (5) in the squeegee body's pre-assembly (
Fig.6
).
7. Remove the front rubber blade (6) from the squeegee's internal body (
Fig.7
).
8. Repeat the operations in reverse order to reassemble all the parts.
N.B.:
Before using the machine, remember to adjust the squeegee body: see the section titled “
”.
N.B.:
It is recommended to replace both squeegee body blades in order to ensure good results when drying the floor.
39
