Fimap MAGNA PLUS, Руководство по эксплуатации и обслуживанию

Страница: 18 / 48

ASSEMBLING THE BRUSH HEAD BRUSHES (SWEEPING VERSION)
To fit the brush on the brush head body, proceed as follows:
1. Make sure the machine has been secured (see the section titled “ SECURING THE MACHINE ”).
CAUTION: these operations must be carried out using protective gloves to avoid any possible contact with the edges or tips of metal
objects.
2. Open the machine's left lateral carter (10) (
Fig.10
).
3. With the brush head in its resting position, turn the knobs (25) that hold the left lateral carter (26) in place anti-clockwise ( Fig.22 ).
4. Remove the left lateral carter (26) ( Fig.23 ).
5. Insert the brush into the tunnel ( Fig.24 ), taking care to make sure that the gearmotor's drive shaft enters the slit in the brush itself.
6. Repeat the previously described operations for the right-hand side as well.
N.B.: In order to be installed correctly, the brushes must form an X when viewed from above in the forward direction of movement
( Fig.25 ).
FITTING THE SIDE BRUSH (SWEEPING VERSION)
To fit the brush on the brush head body, proceed as follows:
1. Make sure the machine has been secured (see the section titled “ SECURING THE MACHINE ”).
CAUTION: these operations must be carried out using protective gloves to avoid any possible contact with the edges or tips of metal
objects.
2. Stand on the right side of the machine.
3. With the brush head in its raised position, remove the knob (27) that secures the lateral brush to the gearmotor, by turning it clockwise for
the right-hand brush, and anti-clockwise for the left-hand brush ( Fig.26 ).
4. Remove the washer (28) holding the lateral brush in place ( Fig.27 ).
5. Insert the side brush, being careful to position the centering hex device (29) correctly in the slot (30) ( Fig.27 ).
6. Fix the brush to the flange using the knob (27), remembering to put the washer (28) in between the knob and the brush (
Fig.28
).
7. Once the brush has been fitted, move on to the one on the left.
ASSEMBLING THE SQUEEGEE BODY
For packaging reasons, the squeegee body comes disassembled from the machine. In order to mount it on the squeegee support, do the
following:
1. Make sure the machine has been secured (see the section titled “ SECURING THE MACHINE ”).
CAUTION: these operations must be carried out using protective gloves to avoid any possible contact with the edges or tips of metal
objects.
2. Unscrew the knobs (30) in the squeegee body pre-assembly ( Fig.30 ).
3. First, insert the left pin (31) on the squeegee body into the left slit (32) in the squeegee support ( Fig.31 ), so that the bushing adheres to the
walls of the slit in the squeegee support.
4. Repeat the same operation for the right pin.
5. Insert the vacuum tube (33) in the sleeve (34) in the squeegee body ( Fig.32 ).
N.B.: Although the squeegee comes pre-adjusted, it is nevertheless recommended to read the section entitled “ ADJUSTING THE
SQUEEGEE BODY RUBBER BLADES ”.
ADJUSTMENT OF DRIVING POSITION
The proper adjustment of the driving position provides a greater sense of comfort when using the machine.
Correct position on the seat: make sure you sit upright and that your back and that your lower back and spine are at 90°.
Seat adjustment: The seat should always be positioned using the pedals as a reference. To adjust the seat, use the lever located under it.
N.B.: The distance should be adjusted so that with the pedals fully pressed to the floor the knees are slightly bent (about 120°).
N.B.: Adjust the distance of the seat so that when pressing the brake pedal it goes as far as it can. This operation should be done with
the machine running so as to pressurise the braking system.
N.B.: If the knee is not bent enough, it is too far from the steering wheel, if however the knee is bent almost 90°then it is too close to the
steering wheel.
18