Fimap 109070 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 104

background image

3.4

Alarms Table

3.4.1

General Alarms

Id Alarm

Meaning

Solution

AL 1

General

EEPROM failure

Detected an Error in the internal memory of the card. Turn off
and on again. If the error persists, replace the card.

AL 2

General

Key-off failure

Return on the key signal. Turn off the machine, wait at least 2
seconds, and then turn it on again. If the problem persists, replace
the key block.

AL 3

General

Undervoltage

Detected supply voltage less than 15V (even instantly). Check
the batteries and their connection and the connection between
the batteries and the main card. If the error persists, replace the
card.

AL 4

General

Overvoltage

Detected supply voltage more than 35V (even instantly). Check
the batteries and their connection and the connection between the
batteries and the main card. If the error persists, replace the card.

AL 5

General

Battery

not

con-

nected

Detected no voltage on the battery poles but present on the key
input (disabled for this machine).

AL 6

General

Keyboard
Communication

No communication between display and main board. Check the
connection between the cards. If the problem persists, replace the
main card or the display card.

AL 7

General

Communication
FFM

Lack of communication between the BB and the main card. Check
the connection between the cards. If the problem persists, replace
the main card or the BB.

AL 8

General

Communication 1

Internal error in the main card BUS data, turn off and on again.
If the problem persists, replace the main card.

AL 9

General

Communication 2

Internal error in the main card BUS data, turn off and on again.
If the problem persists, replace the main card.

AL 10

General

Insert Tag

One of the enabled TAGs is not inserted. Enter one of the enabled
TAGs in the Slot.

AL 11

General

Invalid Tag

The inserted TAG is not enabled. Enter one of the enabled TAGs
in the Slot.

AL 12

General

Update in
progress. . .

The machine is updating the parameter list. Wait for the end of
the operation.

AL 13

General

Restart
the Machine

After updating the parameters (AL 12) indicates that is necessary
to restart the machine.

34

«
...
32
33
34
35
36
...
»

Содержание 109070









































































































Отзывы:

Нет отзывов

Похожие инструкции для 109070

Бренд: Onyx Страницы: 24

TWIST-N-BLITZ 9305

Бренд: Professional Страницы: 8

Бренд: FIORENTINI Страницы: 18

Бренд: GADLEE Страницы: 2

Бренд: VLX Страницы: 34

combimat 300E CO300

Бренд: JohnsonDiversey Страницы: 9

Бренд: Crescent Страницы: 2

Бренд: RCm Страницы: 91

Бренд: RCm Страницы: 93

Бренд: BETCO Страницы: 36

Бренд: i-team Страницы: 35

Бренд: Daewoo Страницы: 30

TOPCLEAN 1200PRO+

Бренд: ulsonix Страницы: 168

Бренд: Lamona Страницы: 16

Бренд: Gansow Страницы: 78

Бренд: Lavorwash Страницы: 32

Бренд: BART Страницы: 24

Бренд: U.S. Products Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды