Filtec FT-50c Скачать руководство пользователя страница 212 | Manualshive

Страница: 212 / 239

Filtec FT-50c Скачать руководство пользователя страница 212

Chapter 8: Diagnostic and Repair Procedures

8-21

•

If the detector power supply led is green, the power supply is
functioning properly. Check the detector because the crystal in
the detector has failed. Replace the SSD.

Optical Sensors

False triggers suddenly increase, or reject timing malfunctions
occur.

1.

Inspect and clean the lenses. Use a cotton swab and isopropyl
alcohol to clean the lense. If the lense is scratched, chipped,
cracked, or discolored, replace it.

2.

Fiber optic strands in the cable may be broken. Remove the
cable from the sensor ampliﬁer and shine a ﬂashlight into the
lense. Looking at the cable end you removed, the light should
be solid and round. If there are any dark spots, the cable
contains ﬁber optic strands. Replace the cable.

Proximity Sensors

No triggering occurs.

•

Check LED 7 on the processor board. If the LED blinks when a
container passes under the sensor, the sensor is working.
Check to be sure the sensor height is set properly. See

Chapter

6: FT-50 Calibration Procedures

for more information.

•

The height of the sensor has been changed. Check to see that
the FT-50 head height has not been altered. See

Chapter 6:

FT-50 Calibration Procedures

for more information.

Encoder

•

The encoder has a built in diagnostic that displays Error 22
when the encoder has failed and must be replaced.

•

If the rejector timing is erratic and you are certain all settings
are conﬁgured properly, the encoder may not be installed
properly, or the encoder coupling may be slipping.

Industrial Dynamics Company, Ltd.

Document 40255-0600

«
...
210
211
212
213
214
...
»

Содержание FT-50c
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды