Filtec FT-50c Скачать руководство пользователя страница 205 | Manualshive

Страница: 205 / 239

Filtec FT-50c Скачать руководство пользователя страница 205

FT-50 Fill Level Inspector Service Manual

8-14

What You Should Do First

Before you begin detailed and time consuming troubleshooting
methods check the following items ﬁrst. These are simple things
that are often overlooked, but can cause a wide range of system
problems:

1.

Is the power turned on?

Verify that both the main power switch on the I/O Junction
Box and the internal power switch located on the power ﬁlter
junction box are turned on.

2.

Is the power ﬁlter circuit breaker tripped?

The internal power switch is an integrated switch/circuit
breaker. When the breaker is tripped, the power switch turns
off. Verify the power switch is turned on, if not turn it on to
reset the breaker.

3.

Is power reaching the FT-50?

Verify the power from the factory power system is reaching the
FT-50 and that the power selector switch is set to the proper
voltage (110v or 220v). The power selector switch is located on
the power ﬁlter junction box.

4.

Are all dip switches and jumpers conﬁgured properly?

Verify the dip switches and jumpers on the processor circuit
board are conﬁgured properly. You can ﬁnd the factory settings
by looking at the Conﬁguration Sheet that is included with
each machine and is stored in the plastic sleeve attached to the
inside of the FT-50 inspection head cover.

Industrial Dynamics Company, Ltd. Document 40255-0600

«
...
203
204
205
206
207
...
»

Содержание FT-50c
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды