Filtec FT-50c Скачать руководство пользователя страница 182 | Manualshive

Страница: 182 / 239

Filtec FT-50c Скачать руководство пользователя страница 182

Chapter 6: Calibration Procedures

6-43

The Dynamic Product Good Test

The Dynamic Good Product Test is used to verify the inspection
accuracy under production conditions. You need 30 good (not
marginal) production containers to perform this test.

If you run this test with actual production ﬂow, the FT-50 will
sense this and automatically change the sample batch size to 128.

1.

Start the conveyor and run it at production speed.

2.

Press the Arrow Key and you are instructed to run thirty good
production containers through the FT-50. Start them far
enough upstream so they do not slide on the conveyor as they
pass through the inspection area. If you are using production
ﬂow the FT-50 automatically samples 128 containers.

The FT-50 must accept all 30 (or 128) containers in order to
establish the Dynamic Good Margin. The Dynamic Good
Margin compensates for ﬁll level variance due to conveyor
motion.

3.

If during this test the message LOW MARGIN, RAISE 2 TICKS
appears, then a container has failed the test. You must raise the
inspection head 2 ticks and then press the Arrow Key to repeat
the test.

4.

When the test is successfully completed you are asked to set
the Underﬁll Threshold. During the Dynamic Reject Point Test
and the Dynamic Product Good Test the threshold is ﬁne
tuned. Press the Arrow Key to accept the new threshold.

5.

The Dynamic Product Good Test is complete. Press Key 1 to
proceed to Review Fill Level Test.

Industrial Dynamics Company, Ltd.

Document 40255-0600

«
...
180
181
182
183
184
...
»

Содержание FT-50c
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды