Filtec FT-50c Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 239

Filtec FT-50c Скачать руководство пользователя страница 132

Chapter 5: System Software

5-37

External Reject

Prepares the FT-50 software for external reject inspection by
inserting the necessary options into the software. When set to Not
Present it removes the options necessary for external reject
inspection from the software.

This function does not activate or deactivate external reject
inspection, it only readies the machine. To turn external reject
inspection on or off you must use the External Reject Status
function.

External Reject Text

Allows you to create a custom name for the External Reject Option.
Any instance in which “External Reject” would have appeared in
the software, is replaced by the custom label you created. The
following options are effected:

•

External Reject Status

•

Total External Reject

•

Reset External Reject

•

Alarm External Reject

•

External Reject Text

•

External Reject

Note

This manual assumes the default name for this option. If you
change the default text remember to substitute the new name
when reading this manual. To avoid confusion record the change
in the manual.

To create a name:

1.

Press the Arrow Key until the desired character appears.

2.

Press Key 6 to advance to the next space.

3.

Repeat steps 1 and 2 until you complete the entry and then
press Key 5 once to enter the text.

Industrial Dynamics Company, Ltd.

Document 40255-0600

«
...
130
131
132
133
134
...
»

Содержание FT-50c
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды