Filtec FT-50c Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 239

Filtec FT-50c Скачать руководство пользователя страница 130

Chapter 5: System Software

5-35

Down Can

Prepares the FT-50 software for down can inspection by inserting
the necessary options into the software. When set to Not Present it
removes the options necessary for down can inspection from the
software.

This function does not activate or deactivate down can inspection,
it only readies the machine. To turn down can inspection on or off
you must use the Down Can Status function.

Down Can Text

Allows you to create a custom name for the Down Can Option.
Any instance in which “Down Can” would have appeared in the
software, is replaced by the custom label you created. The
following options are effected:

•

Down Can Status

•

Total Down Can

•

Reset Down Can

•

Width at Down Can

•

Alarm Down Can

•

Down Can Text

•

Down Can

Note

This manual assumes the default name for this option. If you
change the default text remember to substitute the new name
when reading this manual. To avoid confusion record the change
in the manual.

To create a name:

1.

Press the Arrow Key until the desired character appears.

2.

Press Key 6 to advance to the next space.

3.

Repeat steps 1 and 2 until you complete the entry and then
press Key 5 once to enter the text.

Industrial Dynamics Company, Ltd.

Document 40255-0600

«
...
128
129
130
131
132
...
»

Содержание FT-50c
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды