Filtec FT-50c Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 239

Filtec FT-50c Скачать руководство пользователя страница 118

Chapter 5: System Software

5-23

System Functions Group

Current Container Type

The container type that is currently being inspected. This function
is only available if machine is conﬁgured for multiple container
types.

To select the Current Container Type:

1.

Press Key 5 until CURRENT CONTAINER TYPE appears.

2.

Press the Arrow Key until the desired container type appears.

Last Reject Detected

The type of failure that caused the most recent reject container. The
failure classiﬁcation can be any of the inspection capabilities
installed and active on your system.

Beacon Status

Determines the operational status of the warning beacon. There are
three status choices:

•

On:

the beacon will ﬂash once for each rejected container and

continuously when a diagnostic error occurs. The beacon will
stop ﬂashing when the diagnostic error is cleared.

•

Off:

The beacon will ﬂash once for each rejected container.

•

High Priority Only:

The beacon will ﬂash once for each rejected

container and continuously when a high priority diagnostic
error occurs. The beacon will stop ﬂashing when the diagnostic
error is cleared.

Line Speed (cpm)

The speed of the production line measured by cpm (containers per
minute). The measurement is the number containers that intercept
the FT-50’s trigger beam in 60 seconds. To calculate cpm from cph
(containers per hour) use the following formula:

cph

60

---------

cpm

=

Industrial Dynamics Company, Ltd.

Document 40255-0600

«
...
116
117
118
119
120
...
»

Содержание FT-50c
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды