Filtec FT-50c Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 239

Filtec FT-50c Скачать руководство пользователя страница 112

Chapter 5: System Software

5-17

Counter Functions Group

The Counters record operational and performance data about the
FT-50 and the production line it is operating on. This data is useful
for plant performance management and for machine maintenance.
Here are some other issues you should be aware of:

•

The counters are active only for those functions that are active.
If you disable a function, the associated counter (or counters)
no longer include that function in the count.

•

When you reset a counter, the current count is erased. If you
need the current count, you should record it before you reset
the counter

Total Throughput

Displays the total number of containers that passed through the
trigger beam. The counter automatically resets at 99,999,999.

Total Rejects

The total number of rejected containers. The counter automatically
resets at 99,999,999.

Total Rejects is the sum of the rejections from all active inspection
functions. If two functions reject the same container, only one total
reject count is recorded. The Reject Next Can function is included
in Total Rejects.

Total Underfills

The total number of underﬁlled containers that failed the ﬁll level
inspection. The counter automatically resets at 99,999,999.

Total Overfills

Displays the total number of overﬁlled containers that failed the
ﬁll level inspection. The counter automatically resets at 99,999,999.

Total Missing Lid

The total number of containers that were detected with missing
lids. The counter automatically resets at 99,999,999.

Industrial Dynamics Company, Ltd.

Document 40255-0600

«
...
110
111
112
113
114
...
»

Содержание FT-50c
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды