Fiery X2 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 164

background image

2

2-18

Setting up the Fiery X2

TCP/IP Setup with Token Ring

Enable TCP/IP for Token Ring, and enter the IP address and subnet mask. Then, if
your TCP/IP network has a gateway, and users outside the gateway plan to print to the
Fiery X2 using TCP/IP, choose Gateway Setup and enter the gateway address (see
page 2–19).

IP Address
[127.0.0.1]

Enter the Fiery X2 IP address for Token Ring. The Fiery X2 is shipped with the IP
address set to the loopback address, which is an internal address used for network
checking. If you plan to print with TCP/IP, you must first assign the
Fiery X2 a unique network IP address. For information about setting up printing with
TCP/IP, see Chapter 4.

Network Setup

Protocol Setup

TCP/IP Setup

Token Ring Setup

Enable TCP/IP for Token Ring
Yes/No [No]

Select

Yes

if you have a TCP/IP network connected to the Fiery X2 over Token

Ring.

If you use Token Ring, enabling TCP/IP for Token Ring is required for enabling the
Fiery WebTools.

N

OTE

:

If you are using TCP/IP for printing from Windows NT 4.0 workstations,

enabling TCP/IP here also lets you use the Fiery utilities from Windows NT 4.0
workstations using TCP/IP protocols. At the same time, enabling TCP/IP enables
the network layer that lets you use the Fiery utilities from Windows 95 computers
using IPX/SPX protocols.

«
...
52
53
54
55
56
...
»

Содержание X2





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X2

BladeCenter HS23

Бренд: IBM Страницы: 30

System x3950 X6

Бренд: IBM Страницы: 53

Бренд: ONELAN Страницы: 24

UniServer T1100 G3

Бренд: H3C Страницы: 138

Sun Fire Netra 1280

Бренд: Sun Microsystems Страницы: 10

AcquiLite EMB A7810

Бренд: Obvius Страницы: 29

PRIMERGY CX400 M6

Бренд: Fujitsu Страницы: 209

PRIMERGY CX272 S1

Бренд: Fujitsu Страницы: 234

Primergy CX270 S2

Бренд: Fujitsu Страницы: 320

Primergy CX270 S2

Бренд: Fujitsu Страницы: 56

PRIMERGY RX100 S7

Бренд: Fujitsu Страницы: 86

PRIMERGY RX1330 M1

Бренд: Fujitsu Страницы: 312

Primergy RX100 S4

Бренд: Fujitsu Страницы: 85

PRIMERGY RX1330 M1

Бренд: Fujitsu Страницы: 84

Primergy RX100 S3

Бренд: Fujitsu Страницы: 73

PRIMERGY RX100 S8

Бренд: Fujitsu Страницы: 82

PRIMERGY RX1330 M3

Бренд: Fujitsu Страницы: 342

PRIMERGY RX100 S7

Бренд: Fujitsu Страницы: 490

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды