Fiery X2 Скачать руководство пользователя страница 34

Страница: 34 / 164

1-14

Connecting to the Network

USE

THINNET

CABLE

With

the Fiery X2 turned off, connect the transceiver to the AUI connector on the back

of the Fiery X2. Slide the latch to lock the transceiver connection.

Connect the thinnet cable to the BNC connector on the transceiver.

OTE

If the external transceiver has an SQE switch, make sure the switch is set to OFF.

It should be set to OFF at all times. The functions controlled by the SQE switch are
not required for use with the Fiery X2.

Configure network servers for printing and then proceed to Setup.

USE

THICKNET

CABLE

With the Fiery X2 turned off, connect the thicknet cable connector to the AUI connec-
tor on the back of the Fiery X2. Slide the latch to lock the connector.

Configure network servers for printing and then proceed to Setup.

USE

UTP

CABLE

FOR

100B

ASE

10B

ASE

With the Fiery X2 turned off, connect the RJ-45 cable connector to the Ethernet RJ-45
socket on the back of the Fiery X2.

Configure network servers for printing and then proceed to Setup.

Содержание X2





































































































































































Результаты поиска

Содержание X2

Отзывы:

Fiery X2, Руководство администратора, Страница: 34 / 164

Результаты поиска

Содержание X2

Отзывы: