Fiery E-41 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 161

background image

I

NSTALLATION

22

I

NSTALLATION

This chapter includes information about the following:

• Installation sequence (see below)

• Checking the customer site (see

• Unpacking the E-41 (see

• Installing the E-41 and connecting it to the copier/printer and network (see

• Completing the installation (see

)

–

Print a Test Page and Configuration page (

–

Remind the site administrator to install current user software on networked computers
that print to the E-41 (see

Printing

and

Utilities

on the User Documentation CD).

Installation sequence

Familiarize yourself with this chapter before you attempt an installation. The installation
sequence described in this chapter is designed to make your job as easy as possible. Installation
problems are easier to avoid and diagnose if you proceed from the component to the system
level and verify functionality at each stage.

Figure 3 on page 23

outlines the recommended

installation procedure for connecting the E-41 to the copier/printer.

Because the E-41 is a node on the customer’s computer network, make sure that you
coordinate your scheduled installation with the network administrator at the customer site.
For Network Setup information, refer the network administrator to

Configuration and Setup

on the User Documentation CD.

N

OTE

:

You can change the default language preinstalled at the factory using the Configure

tool available through Command WorkStation and WebTools. Launch Configure and then
navigate to Server > General > Choose Server Language and then click Apply.

«
...
20
21
22
23
24
...
»

Содержание E-41


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E-41

Бренд: BADODOSECURITY Страницы: 8

Бренд: Campbell Страницы: 34

Бренд: Daikin Страницы: 5

Бренд: Danfoss Страницы: 85

VLT Decentral FCD 300

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 4

VLT 6000 series

Бренд: Danfoss Страницы: 27

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 20

ADAP-KOOL AK-PC 781

Бренд: Danfoss Страницы: 14

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 12

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 96

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Digiplex DGP-848

Бренд: Paradox Страницы: 20

Бренд: WABCO Страницы: 4

Бренд: Rayrun Страницы: 4

Бренд: Parker Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды