FIEDLER H1 страница 68 Скачать руководство пользователя | Manualshive

Страница: 68 / 82

background image

Hydro Logger H1

User manual

68

electronics for ecology

FIEDLER

6.9.

Warning and control SMS

Automatic sending of a preset warning or control SMS can be triggered not only
by exceeding the preset limit value on the measuring channel, but also by a
change in the state of the binary channel, an error in the measuring signal, acti-
vation or deactivation of an alarm on the channel, etc.

The  Hydro  Logger  H1  continuously  evaluates  the  current  measured  values  on
both analogue and binary channels. If the value exceeds the set limit or if a binary
input is switched on or off, it sends a pre-prepared SMS to selected mobile pho-
nes.
For integral variables (instantaneous or cumulative flow, rainfall, number of pul-
ses, ...), the activation of the SMS warning can also be triggered by exceeding a
pre-set limit value for a certain time.
Warning messages are the basic and most frequently used type of SMS in the
communicator.  The  features  of  warning  SMS  can  be  summarized  in  the
following points:

▪

The user can set the text of up to fourteen different warning messages.

▪

At the beginning of each alert SMS it is possible to automatically insert
the name of the device sending the message and the current time in the
device at the time of sending the SMS. Only then is the actual text of the
message followed.

Note: in special cases, such as sending a message to a special operator

number that forwards incoming messages to e-mail, it is necessary to di-
sable the automatic insertion of the name tag and time.

▪

For each message, you can select the recipient from a list of authorised
persons. You can also create a group of persons to whom the SMS will
be sent in turn.

▪

The sending of the message can be conditioned by the time period for
which the activation condition of the message must be fulfilled

S t a r t i n g

c o n d i t i o n s

A c t i v a t i o n b y s u m

P r o p e r t i e s o f

w a r n i n g m e s s a g e s

When you select a group as
recipient, the same SMS is
sent to each member of the
group in turn

There are 14 SMS alerts

Phonebook for 10 recipi-
ents that can be grouped
together.

SMS will be sent
only after the conti-
nuous duration of
the trigger condition

Prevents frequent
sending of SMS
when the variable
moves around the li-
mits.

Text without ac-
cents. Special cha-
racters allow auto-
matic insertion of
the instantaneous
value of the mea-
surand.

You can temporarily
or permanently disa-
ble an SMS that you
have already set up.
The set parameters
will be preserved.

Trigger condition, after
which the warning SMS is
activated

Limit value, after which the
warning SMS will be activa-
ted

«
...
66
67
68
69
70
...
»

Содержание H1



















































































Отзывы:

Нет отзывов

Похожие инструкции для H1

Бренд: Campbell Страницы: 690

Бренд: SwitchDin Страницы: 12

Contoil DFM 8EDM

Бренд: aqua metro Страницы: 20

Бренд: XC-Tracer Страницы: 16

CTD-Diver DI28 Series

Бренд: Van Essen Страницы: 34

Бренд: GRAPHTEC Страницы: 158

Бренд: Lambrecht Страницы: 30

Бренд: Solinst Страницы: 8

Бренд: Logicbus Страницы: 4

SENECA Z-LTE-WW

Бренд: Logicbus Страницы: 4

Бренд: Keydemon Страницы: 20

Бренд: Grosvenor Страницы: 32

Бренд: Grosvenor Страницы: 35

Бренд: ELEKON Страницы: 28

Бренд: CyberPower Страницы: 33

Бренд: InTemp Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды