FIEDLER H1 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 82

FIEDLER H1 Скачать руководство пользователя страница 62

Hydro Logger H1

User manual

62

electronics for ecology

FIEDLER

6.6.

GSM parameters

This tab contains parameters related to SMS communication, including access
to SMS phonebook settings.

Recently, the formerly widely used prepaid credit SIM cards have taken a back
seat and the use of flat-rate SIM cards, which usually include a certain amount
of free data, has become more widespread.
For this reason, and also because the information about the remaining credit on
the  prepaid  SIM  provided  by  the  operator  often  changed  in  the  form  and
structure of the informative SMS, the device's FW stopped supporting the auto-
matic calculation of the remaining credit on the prepaid SIM card. Therefore, if
the user selects an option other than 'General flat rate card' in the device para-
meters for the SIM card type, the calculated remaining credit will most likely not
correspond to reality.
The other GSM communication parameters can be left in the basic settings ex-
cept for the command line for setting the content of the periodic or informative
SMS.  This  command  line  should  be  set  according  to  the  actual  channel occu-
pancy and the requirements of the station operator. The list of codes used in
the command line is given in the table on page 2. 65.
Note: The Hydro Logger H1 will also respond to incoming SMS containing indivi-
dual codes separated by commas after the password.

The meaning of other parameters will be explained in chapter 6.8.3. "List of
query and control

" on page 65.

E s t a b l i s h i n g

c r e d i t

Check if you want the
communicator to reply only
to users listed in the phone
book

A  command  line  according
to which the unit composes
an  SMS  message  and
sends it to the number from
which  the  INFO  request
was sent.   Do not set more
than 6-8 commands as the
SMS length is limited to 160
characters.

Password for query SMS
(made of query codes)

Depending  on  the
SIM  card  you  are
using,  select  the
operator  and  card
type  from  the  list.
This option is used to
periodically

check

the credit amount of
the prepaid SIM card

Specifying

credit

check parameters.

After  sending  the
data  to  the  server,
the  GSM  module
can remain logged in
for  a  short  period  of
time for data calls or
for  receiving  and
sending

SMS

messages.

Access to a user-modifiable
phone book.

You can set the time and
day of the week you wish to
receive informative SMS

«
...
60
61
62
63
64
...
»

Содержание H1



















































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды