Fidelity Electronics 19eA Скачать руководство пользователя | Manualshive

Страница: 7 / 62

background image

1. Reminders

1.1 Metrological Legislation

Because of metrological legislation, some metrological parameter settings are limited to be done by authorized
personnel only. Do not attempt to change any parameters under internal function number F60 ~ F99. Contact your
dealer for installation and technical assistance.

1.2 Seal & Serial Number

This instrument is legal for trade only when it is sealed (and/or stamped) and bearing a serial number. Do not attempt
to break the seal (or stamp) or serial number affixed to this instrument. No warranty service will be provided if the seal
(or stamp) or data plate affixed to this instrument is damaged or removed. Always contact your dealer for after sales
service.

1.3 Warm Up Time

Allow warm up period of not less than 60 seconds before calibration and usage. The higher the setup resolution of
the scale, the longer the warm up period is required. In most cases, 120 seconds is a safe warm up period for all
applications. This warm up period is needed to energy all components to reach a stable status.
The internal count value is deemed stable when the internal AD count varies less than 3 counts within 2 seconds.
To  read  the  internal AD  count  value,  enter  internal  function  F1.  The  internal AD  count  value  of  a  not  yet  fully
energized PCB will go up continuously.

1.4 Placing the Weighing Platform

In order to obtain an accurate weighing result, the weighing platform must be placed on a strong and level surface. Avoid
using the platform and this instrument and the weighing platform in any environment where excessive wind flow, vibration
and extreme temperature change exist.

1.5 Cautions

a.

The instrument is not an explosion proof device.

b.

The instrument is not a water proof device.

c.

Do not open the instrument, no user serviceable parts inside. Always contact your dealer for service.

d.

Do not place this instrument in where shock, excessive vibration or extremes of temperature (before or after
installation) exist.

1.6 Support & Service

Always contact your dealer for product information, after sales service and questions when in doubt.

«
...
5
6
7
8
9
...
»

Содержание 19eA































































Отзывы:

Нет отзывов

Похожие инструкции для 19eA

Бренд: Yamaha Страницы: 83

Бренд: Yamaha Страницы: 63

Бренд: A&D Страницы: 102

Бренд: Macnaught Страницы: 4

Бренд: Wavetek Страницы: 43

Бренд: Raytech Страницы: 18

Бренд: Vaisala Страницы: 90

Бренд: Vaisala Страницы: 4

Бренд: Velleman Страницы: 107

Бренд: GMC-I Prosys Страницы: 10

Бренд: S&S Northern Страницы: 5

Бренд: JUMO Страницы: 24

Бренд: DeltaOHM Страницы: 26

Vigilantplant NFBU200-S Series

Бренд: YOKOGAWA Страницы: 24

Бренд: horiba Страницы: 117

Бренд: Sequid Страницы: 111

SignalHawk SH-36S-PC

Бренд: BIRD Страницы: 137

GRAND RHAPSODY PIANO

Бренд: Waves Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды