Fidelity Electronics 19eA Скачать руководство пользователя

Страница: 59 / 62

Appendix F: - Sbarco Printer Installation, Setup & Label Upload Procedures

F.1 Get the below ready before Printer Installation

An appropriate cable to connect printer and computer. This cable usually comes with the printer. If not, contact
your printer supplier.

A serial cable to connect printer and this instrument.

Pin #9 of this cable must be without any connection.

Download BarDrawer software at http://www.sbarcotech.com/cht/download.php?gid=1

F.2 BarDrawer Software & Printer Driver Installation

Turn off the printer, connect computer and printer by cable, and then turn on the printer.

Install BarDrawer software according to the wizard. After that BarDrawer software is installation is done.

Run BarDrawer software.

Click Install Driver under Tools (figure 1 below). Then install printer driver according to the wizard.

After printer driver installation, click Printer Utility under Tools (figure 2 below).

Click Load from Printer (figure 3 below).

Check FW version: -

•

If FW version = 3.0.05 (date = 2020/12/18) or newer, printer installation is done.

•

If FW version is lower than 3.0.05 (date = 2020/12/18), then FW update is necessary. Continue with
below step for FW update.

Download the latest Sbarco Printer FW at

https://www.fi-measurement.com/resource/driversnsoftwares

Open file located of the Sbarco printer FW downloaded.

10.

Doble click on the FW file name to start Firmware Tool.

11.

Click Program (figure 4 below) to start FW update.

12.

Click OK after FW update is completed.

Figure 1

Figure 2

Figure 3

Figure 4

Figure 5

Содержание 19eA































































Результаты поиска

Содержание 19eA

Отзывы:

Похожие инструкции для 19eA

Бренды по названию

Популярные бренды

Fidelity Electronics 19eA, Руководство по эксплуатации

Результаты поиска

Содержание 19eA

Отзывы:

Похожие инструкции для 19eA

Бренды по названию

Популярные бренды