Fidelity Electronics 19eA Скачать руководство пользователя

Страница: 12 / 62

4. Power & Connections

4.1 Power Adaptor

Always use the power adaptor supplied together with this instrument to avoid un-recoverable damages to this instrument.

4.2 Built-In Rechargeable Battery

Before first time use, recharge the built-in batter for at least 8 hours to ensure the best battery performance.

4.3 Connect

with Weighing Platform or Load Cell Junction Box

Connect this instrument with a weighing platform (load cell) through load cell connector located at the back according
to the below pin assignment table.

Note: -

If a 4-wire load cell or junction box is used, short-circuit pin 1&2 and pin 3&4. Otherwise, this instrument will not

work.

4.3.1 Load cell connector pin assignment

Pin # on

Load Cell Connector

Pin Assignment

Excive

Remote Sense +ve

Excitation -ve

Remote Sense -ve

Signal -ve

Ground

4.4 Comports on Instrument

There are 2 built-in comports on this instrument. Both comports support bi-directional communication when set as PC
and CMD modes. Refer to

5.5

for setting details.

4.5 Comports Pin Assignment

Refer to below table for pin assignment between this instrument and a computer or serial printer.

Comport pin assignment on instrument

Notes: -



Comport 1 is assigned as DTE and has a male connector.



Comport 2 is assigned as DCE and has a female connector.

Turn this instrument off and unplug power adaptor before making any connection or disconnection.

Comport 1 (male)

Comport 2 (female)

2 = RXD

2 = TXD

3 = TXD

3 = RXD

5 = GND

5 = GND

9 = DC 5V Output

Nil

Содержание 19eA































































Результаты поиска

Содержание 19eA

Отзывы:

Похожие инструкции для 19eA

Бренды по названию

Популярные бренды

Fidelity Electronics 19eA, Руководство по эксплуатации

Результаты поиска

Содержание 19eA

Отзывы:

Похожие инструкции для 19eA

Бренды по названию

Популярные бренды