manualshive.com logo in svg

FibroLAN Falcon Gen-3 M-Class, Руководство пользователя

Поделиться
Скачать
FibroLAN Falcon Gen-3 M-Class Скачать руководство пользователя страница 415

Falcon 

M-Class

  |  User Guide 

 

415 

Pkts 

The total number of packets (including bad packets, broadcast packets, and multicast 
packets) received. 

Broadcast 

The total number of good packets received that were directed to the broadcast address. 

Multicast 

The total number of good packets received that were directed to a multicast address. 

CECErrors 

The total number of packets received that had a length (excluding framing bits, but 

including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad 
Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad 
FCS with a non-integral number of octets (Alignment Error). 

Undersize 

The total number of packets received that were less than 64 octets. 

Oversize 

The total number of packets received that were longer than 1518 octets. 

Frag. 

The number of frames which size is less than 64 octets received with invalid CRC. 

Jabb. 

The number of frames which size is larger than 64 octets received with invalid CRC. 

Coll. 

The best estimate of the total number of collisions on this Ethernet segment. 

Utilization 

The best estimate of the mean physical layer network utilization on this interface during 
this sampling interval, in hundredths of a percent. 

Buttons 

Auto-refresh

: Check this box to refresh the page automatically. Automatic refresh occurs 

every 3 seconds 

Refresh: 

Click to refresh the page immediately. 

<<

: Updates the the table starting from the first entry in the Alarm Table, i.e. the entry 

with the lowest ID. 

>>: 

Updates the table, starting with the entry after the last entry currently displayed. 

 

5.10.4

 

RMON Statistics Status Overview  

This page provides an overview of RMON Statistics entries. 

Each page shows up to 99 entries from the Event table, default being 20, selected through the 
"entries per page" input field. 
When first visited, the web page will show the first 20 entries from the beginning of the Event table 
The first displayed will be the one with the lowest Event Index and Log Index found in the Event 
table. 
The "Start from Event Index and Log Index" allows the user to select the starting point in the Event 
table. Clicking the Refresh button will update the displayed table starting from that or the next 
closest Event table match. 
The 

>>

will use the last entry of the currently displayed entry as a basis for the next lookup 

When the end is reached the text "No more entries" is shown in the displayed table. 
Use the 

<<

: button to start over. 

 

Содержание Falcon Gen-3 M-Class


























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды