Fibocom SC806 Скачать руководство пользователя страница 34

Страница: 34 / 70

The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval.

SC806Hardware User ManualPage34 of 70

3.5

UARTInterface

The SC806 defines two UART interfaces and three I2Cs. It also supports multiplexed SPI. Please contact our

technical support when you need it.

The SC806 serial interface is 1.8V level. If the peripheral is at other levels, level shift is required.

Table12UART interface pin definition

Pin No.

Pin Name

I/O

Description

Note

UART2_TX

UART2 data transmission

UART2_RX

UART2 data reception

UART2_CTS

UART2 clear transmission

UART2_RTS

UART2 request transmission

UART1_TX

UART1 data transmission, the
default is debug interface

UART1_RX

UART1 data reception, the default
is debug interface

3.6

USIMInterface

The SC806 supports two SIM cards, dual-card dual standby (the software defaults is one card standby), and both

are hot pluggable (requires software configuration).

Table13USIM pin definition

Pin No.

Pin Name

I/O

Description

Note

VDD_USIM1_L14

USIM1 power supply, 1.8V/2.95V

USIM1_DIO

I/O

USIM1 data signal

USIM1_CLK

USIM1 clock signal

USIM1_RST

USIM1 reset signal

Содержание SC806







































































Результаты поиска

Содержание SC806

Отзывы:

Бренды по названию

Популярные бренды

Fibocom SC806, Руководство пользователя по оборудованию

Результаты поиска

Содержание SC806

Отзывы:

Бренды по названию

Популярные бренды