Fibocom SC806 Скачать руководство пользователя страница 32

Страница: 32 / 70

The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval.

SC806Hardware User ManualPage32 of 70

Figure 9Shutdown Time Slot

3.3.3

Sleep/wakeup

During standby, set the KEY_ON/OFF signal low (100ms) and the system will go to sleep. The system supports

automatic sleep. The time from standby to sleep can be configured via software.

In sleep mode, the low KEY_ON/OFF signal can wake up the system.

3.3.4

Reset

KEY_RST_N is the reset output of the module PMIC. When the system crashes or other abnormalities occur, the

low KEY_RST_N signal is greater than 300ms, and the system will be forced to restart.

3.4

USBInterface

The SC806 supports one USB 2.0 interface, and supports two speed modes, full-speed (12Mbps) and high-speed

mode (480Mbps). USB supports OTG function and HUB expansion interface.

USB pin definition is shown in the following table:

Table10USB pin definition

Pin No.

Pin Name

I/O

Description

Note

141,142

VBUS_5V

Device mode, 5V input

USB_DM

I/O

USB signal negative

USB_DP

I/O

USB signal positive

USB_ID

USB OTG detection pin

The USB_VBUS power is a USB power or an adapter. It can be used as a USB plug-in detection and charge the

Содержание SC806







































































Результаты поиска

Содержание SC806

Отзывы:

Бренды по названию

Популярные бренды

Fibocom SC806, Руководство пользователя по оборудованию

Результаты поиска

Содержание SC806

Отзывы:

Бренды по названию

Популярные бренды