manualshive.com logo in svg

Fibocom SC806, Руководство пользователя по оборудованию

Поделиться
Скачать
Fibocom SC806 Скачать руководство пользователя страница 15

 

 

 

The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval.   

SC806Hardware User ManualPage15 of 70 

USBinterface 

Support USB2.0 high speed mode, data transmission rate up to 480 Mbps 
Support USB OTG (add 5V power supply chip) 

SIMinterface 

2 sets USIM card interface 

Support USIM/SIM card: 1.8V and 2.95V 
Support dual card dual standby (software support required) 

UARTinterface 

2 sets serial ports 

A set four-wire serial port supporting RTS and CTS hardware flow control 

A set two-wire serial port for Debug   
Maximum speed to 4Mbps 

SDIOinterface 

Support SD3.0, 4bit SDIO; SD card supports hot plug 

I2Cinterface 

3 sets I2C, high speed up to 3.4Mbps for TP, Camera, Sensor and other 
peripherals 

ADCinterface 

3 sets for input voltage detection, battery temperature detection, and universal 
ADC 

Real-time clock   

Support 

Antennainterface 

MAIN antenna, DRX antenna, GNSS antenna, WIFI/BT antenna interface 

Physical characteristics 

Size: 40.5mm * 40.5mm * 2.85mm 

Package: 146 LCC pin + 64 LGA pin 
Weight: about 9.2g 

Temperature range 

Operating temperature: -30°C - 70°C 

1)

 

Storage temperature: -40°C - 85°C 

Software update 

Via USB/OTA/SD 

RoHS 

RoHS Compliant 

 

Note: 

1

）

 

When the module is operating in this temperature range, the functions of the module are normal, and the 

relevant performance of the module meets the 3GPP standard. 

 

2.3

 

Hardware Diagram 

The following hardware diagram shows the main hardware functions of the SC806 module, including the 

following: 

 

Baseband 

 

Wireless transceiver 

 

PMU 

 

Storage 

 

Peripheral interface 

-- Communication expansion interface (USB/UART/I2C/SDIO) 

Содержание SC806







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды