Fibocom L860-GL Скачать руководство пользователя

Страница: 67 / 254

FIBOCOM L860 AT Commands User Manual

Page 67 of 254

Command

Description

AT+CTZU=0

AT+CTZU?

+CTZU: 0

Reference

3GPP TS 27.007

5.1.3 +CTZR, Time Zone Reporting

This command enables/disables the time zone change event and Daylight saving time reporting.

Command

Description

Set

[Function]

This set command controls the time zone change event reporting. If reporting is

enabled the MT returns the unsolicited result code +CTZV: <tz>,

+CTZE: <tz>,<dst>,[<time>], or +CTZEU: <tz>,<dst>,[<utime>]

whenever the time zone is changed. The MT also provides the time zone upon network

registration if provided by the network.

[Syntax]

AT+ CTZR = <reporting>

[Response/Action]

or:

+CME ERROR: <err>

Read

[Function]

Read command returns the status of the time zone change event reporting

(enable/disable) (on/off).

[Syntax]

AT+ CTZR?

[Response/Action]

+CTZR: < reporting >

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды