Fibocom L860-GL Скачать руководство пользователя страница 60

Страница: 60 / 254

FIBOCOM L860 AT Commands User Manual

Page 60 of 254

Command

Description

Reference

3GPP TS 27.007

4.4 Error Handling Commands

4.4.1 +CMEE, Report Mobile Equipment Error

The Set command disables or enables the use of result code +CME ERROR: <err> as an indication of an

error relating to the functionality of the MODEM. When enabled, Modem -related errors cause a +CME

ERROR: <err> final result code instead of the regular ERROR final result code. Usually, ERROR is

returned when the error is related to syntax, invalid parameters or terminal functionality.

For all Accessory AT commands besides SMS commands, the +CMEE set command disables or enables

the use of result code +CME ERROR: <err> as an indication of an error relating to the functionality of the

Modem. When enabled, Modem related errors cause a +CME ERROR: <err> final result code instead of

the regular ERROR result code.

For all SMS AT commands that are derived from GSM 07.05, the +CMEE Set command disables or

enables the use of result code +CMS ERROR: <err> as an indication of an error relating to the

functionality of the modem. When enabled, modem -related errors cause a +CMS ERROR: <err> final

result code instead of the regular ERROR final result.

Command

Description

Set

[Function]

The Set command enables or disables the use of result code +CME ERROR: <err> as

an indication of an error relating to the functionality of the Modem.

[Syntax]

AT+CMEE=[<n>]

[Response/Action]

or:

+CME ERROR: <err>

Read

[Function]

The Read command returns the current setting format of the result code.

[Syntax]

AT+CMEE?

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды