Fibocom L860-GL Скачать руководство пользователя страница 33

Страница: 33 / 254

FIBOCOM L860 AT Commands User Manual

Page 33 of 254

Command

Description

Parameters

<value>

Transmits limited headers and trailers, and numeric text.

Transmits full headers and trailers, and verbose response text.

The default value is 1.

Example

ATV1

ATV00

4.1.2 Q, Result Code Suppression

This command determines whether to output the result codes. Information text transmitted in response to

commands is not affected by the setting of this parameter.

Command

Description

Execution

[Function]

The Execution commands sets whether or not to output result codes.

[Syntax]

ATQ<value>

[Response/Action]

or:

+CME ERROR: <err>

Read

N/A

Test

N/A

Parameters

<value>

Transmit result codes.

Suppress result codes.

The default value is 0..

Example

ATQ0

ATQ1

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды