Fibocom L860-GL Скачать руководство пользователя

Страница: 184 / 254

FIBOCOM L860 AT Commands User Manual

Page 184 of 254

Command

Description

Reference

9.1.23 +XADPCLKFREQINFO, Adaptive Clock Frequency Info

This execution command returns the list of frequency information structures. The

frequency information includes the center frequency of the channel number, frequency

spread of the channel number and the noise power referred at antenna.

Command

Description

Set

[Function]

Set command enables/disables the +XADPCLKFREQINFO URC

URC will be: +XADPCLKFREQINFO: <centFreq>, <freqSpread>, <noisePower>

[Syntax]

AT+XADPCLKFREQINFO=<n>

[Response/Action]

CME ERROR: <error>

Read

[Function]

Read command returns the list of frequency information available.

[Syntax]

AT+XADPCLKFREQINFO?

[Response/Action]

+XADPCLKFREQINFO:<n>

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды