Fibocom L860-GL страница 183 Скачать руководство пользователя

Страница: 183 / 254

FIBOCOM L860 AT Commands User Manual

Page 183 of 254

9.1.22 +XSYSTRACE, Configure System Trace

This command allows to configure system trace port, mode.

Command

Description

Set

[Function]

Execution command allows to configure system trace port, mode

[Syntax]

AT+XSYSTRACE=<mode>,["<master>=<port>[;<master>=<port>[;]]"],["<master>=<co

nfig>[;<master>=<config>[;]]"],["[oct=<oct_mode>][;pti1=<pti1_mode>][;pti2=<pti2_mod

e>]"]

[Response/Action]

CME ERROR: <error>

Test

[Function]

Test command returns list of supported <mode>s],[list of supported "<master>

=<port>"s],[list of supported "<master>=<config>s]",[list of supported oct=<oct_

mode>],[;pti1=<pti1_mode>],[;pti2=<pti2_mode>"s].

[Syntax]

AT+ XSYSTRACE =?

[Response/Action]

+XSYSTRACE:[list of supported <mode>s],[list of supported "<master>=<port>"s],[list

of supported "<master>=<config>s]",[list of supported

oct=<oct_mode>][;pti1=<pti1_mode>][;pti2=<pti2_mode>"s]

Limitation

The total length of parameters in set command cannot exceed 400 characters due to

C-AT parser limitation. For set command with total parameter length exceeding 400

characters, multiple set commands by splitting the parameters can be issued.

Example

at+xsystrace=0,"bb_sw=1","bb_sw=sdl:th,tr,st,pr,mo,lt,db,li,sy|lte_stk:0x02,0x83FFFFF
F|ims:1|lte_stk:0x01,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF","oct=4;o
ct_fcs=16"

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды