Fibocom L860-GL Скачать руководство пользователя страница 153

Страница: 153 / 254

FIBOCOM L860 AT Commands User Manual

Page 153 of 254

Command

Description

Reference

3GPP TS 27.007

9.1.7 +CEREG, EPS Network Registration status

The set command controls the presentation of an unsolicited result code +CEREG:<stat> when <n>=1

and there is a change in the MT's EPS network registration status, or code +CEREG:

<stat>[,<tac>,<ci>[,<AcT>]] when <n>=2 and there is a change of the network cell, code +CEREG:

<stat>[,<tac>[,<ci>[,<AcT>[,<reject type>[,<reject cause>]]]]] when <n>=3.

Note1:

If the EPS MT also supports circuit mode services and/or GPRS services, the +CREG command

and +CREG: result codes and/or the +CGREG command and +CGREG: result codes apply to

the registration status and location information for those services.

The read command returns the status of result code presentation and an integer <stat> which shows

whether the network has currently indicated the registration of the MT. Location information elements

<tac>, <ci> and <AcT>, if available, are returned only when <n>=2 and MT is registered in the network.

Test command returns the range of supported network registration mode (i.e. <n>).

Note:

This command is supported only in R8 protocol with LTE.

Command

Description

Set

[Function]

The Set command controls the presentation of an unsolicited result code "+CEREG: "

and the result of the Read operation.

[Syntax]

AT+CEREG=[<n>]

[Response/Action]

+CME ERROR: <err>

Read

[Function]

[Syntax]

AT+CEREG?

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды