Fibocom L860-GL страница 144 Скачать руководство пользователя

Страница: 144 / 254

FIBOCOM L860 AT Commands User Manual

Page 144 of 254

Command

Description

The default value is 61.

<T1>

Acknowledgement timer T1. 39-255.

The default value is 48.

<N2>

Retransmission attempts N2 in integer format (refer to GSM 04.22

subclause5.4.3)

The default value is 6.

Example

AT+CRLP=?

+CRLP: (0-61),(0-61),(39-255),(1-255)

AT+CRLP?

+CRLP: 61,61,48,6

Reference

3GPP TS 27.007

9.1.4 +CREG, Network Registration Status

This command controls the presentation of an unsolicited result code +CREG and provides the

information of network registration status.

Set command is used to control the unsolicited result code +CREG. The syntax of unsolicited result

+CREG as mentioned below:

1. +CREG:<stat> when <n>=1 and there is a change in the MT’s circuit mode network registration

status in GERAN/UTRAN/E-UTRAN.

2. +CREG:<stat> [,<lac>,<ci>[<,<AcT>]] when <n>=2 and there is a change of the network cell cell in

GERAN/UTRAN/E-UTRAN in this case <AcT>,<lac> and <ci> are sent only is available

3. +CREG: <stat> [, <lac>,<ci>[,<AcT>[,<reject type>[,<reject cause>]]]] when <n>=3.

Read command returns the status of result code presentation and an integer <stat> which shows whether

the network has currently indicated the registration of the MT. Location information elements<AcT>,<lac>

and <ci> are returned only, if available,when <n>=2 and MT is registered in the network.

Test command returns the range of supported modes(i.e.<n>s)

Command

Description

Set

[Function]

The Set command controls the presentation of an unsolicited result code and the result

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды