Fibocom FM350-GL Скачать руководство пользователя страница 22

Страница: 22 / 59

FM350-GL Hardware Guide

Page 22 of 59

Module Shutdown

Module can be shut down by following control:

Shutdown Control Action

Condition

Software

Sending AT+CFUN=0 command

Normal shutdown(recommend)

Hardware

Pull down FCPO# pin

Only used when a hardware exception
occurs and the software control cannot be
used.

Module can be shut down by sending AT+CFUN=0 command. When the module receives the software

shutdown command, the module will start the finalization process (the reverse process of initialization),

and it will be completed after t

time (t

is the time which AP receive OK of “AT+CFUN=0”, if there is no

response, the max t

is 5s). In the finalization process, the module will save the network, SIM card and

some other parameters from memory, then clear the memory and shut down PMU. The software control

timing is shown in Figure 3-6:

+3.3V

PERST#

RESET#

Module State

Finalization

Activation

FCPO#

off1

OFF

AT+CFUN=0

off2

Figure 3-6 Software control power off timing

Index Min.

Recommended Max.

Comments

off1

16ms

20ms

RESET# should be asserted after PERST#

off2

2ms

10ms

FCPO#

should be asserted after RESET#

10ms

100ms

+3.3V power supply goes down time. If power supply is

always on, it can be ignored

Module Reset

The FM350 module can reset to its initial status by pulling down the RESET# signal for more than 2ms

(10ms is recommended), and module will restart after RESET# signal is released. When customer

executes RESET# function, the PMU remains its power inside the module. The recommended circuit

design is shown in the Figure 3-7:

Содержание FM350-GL

























































Результаты поиска

Содержание FM350-GL

Отзывы:

Fibocom FM350-GL, Руководство по оборудованию, Страница: 22 / 59

Результаты поиска

Содержание FM350-GL

Отзывы: