Fibocom FG621-LA Series Скачать руководство пользователя страница 54

Страница: 54 / 57

FIBOCOM FG621-LA Series Hardware Guide

Page 54 of 57

interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate this equipment. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

List of applicable FCC rules

This module has been tested and found to comply with part 22, part 24, part 27 requirements for Modular

Approval.

The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter

rules) listed on the grant, and that the host product manufacturer is responsible for compliance to

any other FCC rules that apply to the host not covered by the modular transmitter grant of

certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also

contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that

the final host product still requires Part 15 Subpart B compliance testing with the modular

transmitter installed.

This device is intended only for OEM integrators under the following

conditions: (For module device use)

1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and

2) The transmitter module may not be co-located with any other transmitter or antenna.

As long as 2 conditions above are met, further transmitter test will not be required. However, the

OEM integrator is still responsible for testing their end-product for any additional compliance

requirements required with this module installed.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20 cm between the radiator &

your body.

Содержание FG621-LA Series


























































Результаты поиска

Содержание FG621-LA Series

Отзывы:

Похожие инструкции для FG621-LA Series

Бренды по названию

Популярные бренды

Fibocom FG621-LA Series, Руководство по оборудованию

Результаты поиска

Содержание FG621-LA Series

Отзывы:

Похожие инструкции для FG621-LA Series

Бренды по названию

Популярные бренды