manualshive.com logo in svg

FIBARO ROLLER SHUTTER 3, Руководство пользователя

Поделиться
Скачать
FIBARO ROLLER SHUTTER 3 Скачать руководство пользователя страница 1

  

 

Fibaro  

Roller Shutter 3  

SKU: FIBEFGR-223  

 
 
 

Quickstart 

This is a 

secure Roller Shutter 

for 

Europe

. To run this device please connect it to your mains 

power supply. To add this device to your network execute the following action:  
Quickly, triple click the S1 switch.  

 

Important safety information 

Please read this manual carefully. Failure to follow the recommendations in this manual may be 
dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be 
liable for any loss or damage resulting from failure to comply with the instructions in this manual 
or any other material. Use this equipment only for its intended purpose. Follow the disposal 
instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat 
sources.  

What is Z-Wave? 

Z-Wave is the international wireless protocol for communication in the Smart Home. This device 
is suited for use in the region mentioned in the Quickstart section.  

Содержание ROLLER SHUTTER 3


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды