Fiat Punto 2004 Скачать руководство пользователя страница 361

Страница: 361 / 533

ELECTRIC

DRIVE

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

7 Electric drive

7.1 Description

All the Nuova Punto versions are equipped with electric power steering (E.P.S.).

The Nuova Punto steering control has been designed to minimize the driver’s effort on the

steering wheel during the parking manoeuvres, combined with accuracy and safety during

high-speed driving.

2.8 steering wheel turns are required for full stop-to-stop steering, and the kerb-to-kerb

steering diameter is 10.1 m (vehicles equipped with long-travel rack and 175 tyres ) or 10.76

m (vehicles equipped with short-travel rack and any other type of tyre).

The electric power steering is actuated by an electric motor that is more compact and

lightweight compared with the previous systems.

gb Fiat Grande Punto OK

361 / 532

It is made up of a steering column with integrated, electric drive system, and a special

management control unit.

Содержание Punto 2004

































































































































































































































































































































































































































































































































Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды

Fiat Punto 2004, Руководство по обучению

Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды