Festool MFK 700 EQ, Инструкция по эксплуатации

Страница: 18 / 87

► Tighten the screw [5-4] to clamp the ex­
traction hood in position.
Removal in reverse order.
7.3
Changing tools
CAUTION
Risk of injury from hot and sharp insertion
tool
► Do not use any blunt or faulty insertion
tools.
► Wear protective gloves when handling an
insertion tool.
Before replacing the cutter remove the router
table.
Removing the tool
► Push spindle lock [6-1].
► Slacken union nut [6-2] using open ended
spanner (SW 19) until the tool can be re­
moved.
► Release spindle lock [6-1].
Inserting the tool
► Position the cutter [6-3] as far as possible,
at least as far as the marking at the
cutter shaft, into the open clamping collet.
► Push spindle lock [6-1].
► Tighten union nut [6-2] using open ended
spanner (SW 19).
► Release spindle lock [6-1].
7.4
Replacing clamping collet
Only suitable tools can be used with the sup­
plied collets. Collets with 8 mm, 6 mm and 1/4"
(6.35 mm) can be used.
► Push spindle lock [7-1].
► Unscrew union nut [7-2] fully.
► Release spindle lock [7-1].
► Remove union nut together with the clamp­
ing collet [7-3] from the spindle. Never
separate the union nut and clamping col­
let! They form one unit.
► Insert another clamping collet with union
nut into the spindle.
► Gently turn union nut. Do not tighten union
nut if there is no cutter inserted!
7.5 Setting the Mortise Depth
► Unscrew the rotary knob [8-3] and the
clamp [8-1] (large surface router table on­
ly).
► Turn the rotary wheel [8-2] to set the router
table to the required routing depth.
► Tighten the rotary knob [8-3] and the
clamp [8-1] (large surface router table on­
ly).
7.6 Dust extraction
WARNING
Dust hazard
► Dust can be hazardous to health. Always
work with a dust extractor.
► Always read applicable national regula­
tions before extracting hazardous dust.
Extraction hoods are supplied for both router
tables; a Festool extractor (extractor hose with
a diameter of 27 mm) can be connected to
these extraction hoods.
The dust extractor (extractor hose with dia. 27
mm) can also be attached to the large surface
router table or the side stop depending on the
application.
CAUTION! If an anti-static suction hose is not
used, static charge may occur. The user may
receive an electric shock and the electronics of
the power tool may be damaged.
8 Working with the electric
power tool
When working on the machine, observe
all of the safety warnings that are listed
at the start as well as the following rules:
–
Always secure the workpiece in such a way
that it cannot move during machining.
– Hold the machine with two hands – one on
the motor housing and one on the gear
head or on the additional handle [1-5] – to
ensure safe guidance.
– Adjust the feed speed to the router diame­
ter and the material. Work with a constant
feed speed.
– Only guide the power tool towards the
workpiece when it is switched on.
– Wait until the power tool has come to a
complete halt before placing it down. The
insertion tool can get caught and lead to a
loss of control of the power tool.
– Make sure that the router table is firmly
tightened before routing.
– When routing, ensure that the power tool's
feed direction is the same as the tool's cut­
ting direction.
English
18