manualshive.com logo in svg

Festo EMCS-ST, Руководство по эксплуатации

Поделиться
Скачать
Festo EMCS-ST Скачать руководство пользователя страница 77

Process parameters

System parameters

Description

"Mov

In

"

"Mov

Out

"

System commands

0x0029.1

0x0029x2

0x0002

–

In end-to-end operation with press func-
tion, the drive travels from the "Start
Press" position towards the "Lim

Out

" end

position under force control.

–

After a restart, the reference end position
"Ref" is re-initialised first.

true

false

Mov

In

0xC8
(200)

Control command for executing the motion
"Mov

In

".

–

The drive moves position-controlled
towards the "Lim

In

(Ref)" end position.

–

After a restart, the reference end position
"Ref" is re-initialised first.

true

true

Disable power stage
0xCB
(203)

Control command for switching off the power
stage.
–

The power stage is switched off immedi-
ately.

–

The drive coasts to a standstill.

–

At standstill, the drive remains stopped
unregulated.

Tab. 39 Control data via IO-Link

14.2.6

Monitor end-to-end operation via IO-Link

The current position of the drive in end-to-end operation can be monitored via the process paramet-
ers. The following table shows the process commands for monitoring the drive position.
The following table shows the combinations of the process parameters "State

In

" and "State

Out

" via IO-

Link for monitoring the drive in end-to-end operation.

Process parameters

Description

"State

In

"

0x0028.1

"State

Out

"

0x0028.2

false

false

–

The drive is not in the "Lim

In

(Ref)" or "Lim

Out

" end position.

false

true

–

The drive is in the "Lim

Out

" end positions.

–

The drive has reached the set force in the force-controlled range of
end-to-end operation with press function.

true

false

–

The drive is in the "Lim

In

(Ref)" end positions.

true

true

–

critical error 

è

 13.2.2 Diagnostic messages and fault clearance.

Tab. 40 Status data via IO-Link

IO-Link

77

Festo — EMCS-ST — 2020-04a

Содержание EMCS-ST























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды