Festo ELGS-BS Series, Инструкция по эксплуатации

Страница: 1 / 4

Translation of the original instructions
© 2020 all rights reserved to Festo SE & Co. KG
IO-Link
®
is a registered trademark of its respective trademark holder in certain
countries.
1 About this document
1.1 Applicable Documents
All available documents for the product è www.festo.com/sp.
Type Product Contents
EMCS-ST Integrated drive Operating instructions
ELGC-BS Spindle axis Operating instructions
EAMM-A Axial kit Assembly instructions
NEFC-M12G8-0.3-M12G5-LK Adapter Assembly instructions
Tab. 1 Other Applicable Documents for the Product
2 Safety
2.1 Safety instructions
– Observe labelling on the product.
– Prior to assembly, installation and maintenance work: Switch off power sup-
ply, ensure that it is off and secure it against being switched back on.
– Store the product in a cool, dry, UV-protected and corrosion-protected envir-
onment. Ensure that storage times are kept to a minimum.
– Observe tightening torques. Unless otherwise specified, the tolerance
is ± 20 %.
2.2 Intended Use
The spindle axis unit ELGS-BS is designed for linear movement of payloads or as a
drive when external guides are used between two end positions.
The spindle axis unit ELGS-BS is approved for slide operation.
Fig. 1 Slide mode
2.3 Training of qualified personnel
Installation, commissioning, maintenance and disassembly should only be con-
ducted by qualified personnel.
The personnel must be familiar with the installation of mechatronic control sys-
tems.
3 Further information
– Accessories è www.festo.com/catalogue.
– Spare parts
è
www.festo.com/spareparts.
4 Service
Contact your regional Festo contact person if you have technical questions
è www.festo.com.
5 Product overview
5.1 Scope of Delivery
The following components are included in the scope of delivery:
–
Spindle axis unit ELGS-BS
– Instruction manual for the spindle axis unit ELGS-BS
– Adapter for IO-Link operation (optional accessory)
è
www.festo.com/catalogue
5.2 System overview
1 PELV fixed power supply for load
voltage
2 PELV fixed power supply for logic
voltage
3 Application software
4 PC or Laptop
5 Controller or IO-Link master
6 Spindle axis unit ELGS-BS
Fig. 2 System Overview
Items 1 … 5 are not in the scope of delivery.
5.2.1 Product design
1 Spindle axis ELGC-BS
2 Axial kit EAMM
3 Product labelling
4 Integrated drive EMCS-ST
5 Controller housing
6 Warning symbol "Attention! Hot
surface"
Fig. 3 Product design
Electrical connections, display and operating components (HMI)
1 LED display Menu
(Speed Out, ..., Demo)
2 LED parameter display
3 LED C/Q
4 Connection for load voltage
[Power]
5 Logic voltage and digital I/O or
IO-Link connection [Logic]
6 Pushbutton actuator (right arrow)
7 Pushbutton actuator (Edit)
8 Pushbutton actuator (left arrow)
Fig. 4 Electrical connections, display and operating components (HMI)
6 Transport
NOTICE!
Unexpected and unbraked movement of components
• Secure moving components for transport.
1. Take product weight into account è 13 Technical data.
2. Maintain support clearance
£
300 mm when attaching transportation aids.
7 Assembly
WARNING!
Risk of injury due to unexpected movement of components.
The drive can move freely in the voltage-free state. This can cause unexpected
movements of the connected mechanics and crush parts of the body.
•
Bring moving parts of the mechanical system into a safe position.
8133151
ELGS-BS
Spindle axis unit
8133151
2020-03a
[8133153]
Operating instructions
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com