Festo DGC G Series Скачать руководство пользователя страница 33

Страница: 33 / 136

33 / 48

Festo 07DGC-Ga_en

Linear drives DGC-50/63-…-G

4.3

Dismantling the linear drive

4.3.1

Place the linear drive on the work surface with the slide facing upwards.

•

Unfasten and remove the four self-tapping screws on both end caps.

•

Note

The basic principle of self-tapping screws means they have a high level of
holding force in the thread and require greater force when unfastening them.

Remove the end caps from the cylinder barrel at both ends of the drive.

•

Remove the sealing rings from the inside of the end caps and the buffers.

•

Documents

Chapters 4.3.4 and 4.3.5 describe how to dismantle and repair the end caps.

Unscrew and remove the flat head screw from the band clamping mechanism

•

on both buffers.

Remove the clamping mechanism for the cover band from both ends of the

•

drive and remove the clamping mechanism from the sealing band between
the cover band and sealing band.

Содержание DGC G Series









































































































































Результаты поиска

Содержание DGC G Series

Отзывы:

Похожие инструкции для DGC G Series

Бренды по названию

Популярные бренды

Festo DGC G Series, Инструкции по ремонту

Результаты поиска

Содержание DGC G Series

Отзывы:

Похожие инструкции для DGC G Series

Бренды по названию

Популярные бренды