Festo CPX-FB23 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 122

background image

1. Installation

1−29

Festo P.BE−CPX−FB23−EN en 0308NH

1.4

Pin assignment for power supply

Warning

Use  only  power  units  which  guarantee  reliable  isolation  of
the  operating  voltages  as  per  IEC  742/EN  60742/VDE  0551
with  at  least  4  kV  isolation  resistance  (Protected  Extra  Low
Voltage  PELV).  Switch  power  packs  are  permitted,  provid
ing  they  guarantee  reliable  isolation  in  accordance  with
EN60950/VDE0805.

By  the  use  of  PELV  power  units,  protection  against  electric
shock  (protection  against  direct  and  indirect  contact)  is  guar
anteed  in  accordance  with  EN  60204−1/IEC  204.  Safety  trans
formers  with  the  adjacent  symbol  must  be  used  for  supplying
PELV  networks.  The  device  must  be  earthed  to  ensure  that  it
functions  correctly  (e.g.  EMC).

The current consumption of a CPX terminal depends on the
number and type of integrated modules and components.

Read the information on power supply as well as on the
earthing measures to be carried out in the CPX system
manual.

«
...
41
42
43
44
45
...
»

Содержание CPX-FB23



























































































































Отзывы:

Нет отзывов

Похожие инструкции для CPX-FB23

Бренд: Nelsen Corporation Страницы: 16

Бренд: National Instruments Страницы: 34

Бренд: Tapeswitch Страницы: 13

Бренд: K&K Страницы: 6

Бренд: National Instruments Страницы: 40

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 22

Бренд: Dahua Страницы: 137

Бренд: M-system Страницы: 13

Бренд: GEA Страницы: 13

Бренд: Climatisation Страницы: 52

Бренд: TECOM Страницы: 8

Бренд: B meters Страницы: 2

TITAN CONTROLS KRONUS 2

Бренд: Sunlight Supply Страницы: 4

Бренд: OmarLift Страницы: 50

Бренд: M-system Страницы: 3

Бренд: Trikdis Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды