Festo CPX-CMAX Скачать руководство пользователя

Страница: 70 / 98

Diagnostics and error handling

Festo – P.BE-CPX-CMAX-SYS-EN – en 2017-09b – English

6.4.4

Error and warning numbers

Information on the error level and on the reset type

Sections 6.4.1 and 6.4.2.

FCT supplies additional information on many diagnostic events (

FCT). Internally, the

additional information is stored in the PNU 203 (

Description of communication profile,

P.BE-CPX-CMAX-CONTROL-...).

Group 0 − Configuration errors

CPX error group 100

(CPX-MMI: [Configuration error] )

No.

Message

Error level Reset type

The nominal configuration deviates from the actual configuration

Note

The movement test is reset to avoid tubing connection errors. The CMAX has C03

status. The movement test should then be run once more.

Cause

A component on the axis string does not correspond to the nominal configuration:

–

displacement encoder or sensor interface (type, length)

–

cylinder (type, length, diameter)

–

valve type

Measure

Check component. Replace defective or incorrect components.

Adopt actual configuration (download).

Cause

The displacement encoder and valve have been exchanged and no longer match

the target configuration or the serial numbers have changed.

Measure

Check the axis configuration. Check to make sure 2 axis strings have not

been interchanged.

Unknown valve

Cause

Connected valve is not supported.

Measure

Replace valve or

Update firmware.

Unknown cylinder

Cause

Connected cylinder or sensor interface is not supported.

Measure

Replace cylinder or sensor interface.

Update firmware.

Unknown displacement encoder or unknown sensor interface

Cause

Connected displacement encoder or sensor interface is not supported.

Measure

Replace displacement encoder or sensor interface.

Update firmware.

Project not loaded completely or block download active

Cause

Drive cannot be enabled because the target configuration is not yet complete

(configuration status C00, C01 or C02).

Measure

Complete the target configuration, e.g. download project again.

Cause

Drive cannot be enabled because the block download is still active.

Measure

End block download. Check and correct the control program (parameterisation).

Содержание CPX-CMAX



































































































Результаты поиска

Содержание CPX-CMAX

Отзывы:

Похожие инструкции для CPX-CMAX

Бренды по названию

Популярные бренды

Festo CPX-CMAX, Описание

Результаты поиска

Содержание CPX-CMAX

Отзывы:

Похожие инструкции для CPX-CMAX

Бренды по названию

Популярные бренды