manualshive.com logo in svg

Festo CPX-CMAX, Описание

Поделиться
Скачать
Festo CPX-CMAX Скачать руководство пользователя страница 25

3

Mounting and pneumatic installation

Festo – P.BE-CPX-CMAX-SYS-EN – en 2017-09b – English

25

3.3.4

Load

For good positioning behaviour, the CMAX must be adjusted to the load. The total load represents the

complete load to be moved with the positioning drive, including the weight of the piston and the slide.

The total load consists of the following:

Load

Description

Base load

Total of all loads/mass moment of inertia of moved components that are

permanently connected to the piston rod/rotary vane or the drive slide of the

cylinder/semi-rotary drive and cannot be changed (e.g. piston/piston rod and

slide, workpiece gripper or gripper unit).

Payload

An additionally moved load of a workpiece or of the load to be transported

which, compared to the constantly present base load, is moved only when the

axis is loaded.

With semi-rotary drives, the payload equals the mass moment of inertia (MMI) of

the workpiece related to the axis of rotation (MMI of the payload in kgcm²).

If the payload is permanently connected to the drive, the load can also be added

to the base load. The payload is then set to zero.

Tab. 3.2

There is a maximum and a minimum permissible total load. The permitted mass load depends on the:

–

drive type

–

drive diameter

–

mounting position

–

operating pressure

 Make sure that the effective total load in all load situations:

–

is not less than the minimum permissible total load. This applies in particular for the load

without payload (

è

 Tab. 3.3 and Tab. 3.5).

–

does not exceed the maximum permissible total load (

è

 Tab. 3.3 and Tab. 3.5).

Note

A pneumatic positioning axis should be operated with at least the minimum total load

(

è

 www.festo.com/catalogue). If necessary, this minimum mass load must be ensured

through the use of an additional weight.

The payload present can be specified for each positioning command. The controller setting of the CMAX

can thus be adjusted to various loads.

Note

If the total load varies from positioning command to positioning command, e.g. due to

changing workpieces, the payload should be adapted in the positioning command. For

additional information 

è

 Communication profile description, P.BE-CPX-CMAX-CONTROL-... .

Содержание CPX-CMAX



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды