background image

PROFIBUS connection [DP-OUT]

Socket M12, 5-pin, B-coded

Signal

1

VP

Supply voltage positive (P5V)

2

RxD/TxD-N

Received/transmitted data N

3

DGND

Data reference potential (M5V)

4

RxD/TxD-P

Received/transmitted data P

5

n.c.

Thread

FE

Functional earth

Tab. 9 PROFIBUS connection

6

Assembly

Assemble the module as outlined in the “Instruction manual for automation system
CPX-AP"

è

 1.1 Other applicable documents.

7

Installation

Carry out the installation according to the "Instruction manual for automation system CPX-AP"

è

 1.1 Other applicable documents.

PROFIBUS Use network cables as described in the cable specification 

è

 12 Technical data.

8

Commissioning

1. Set up an automation project for the higher-order controller using suitable software.
2. Import the device description file into the software 

è

 www.festo.com/sp.

3. Configure the automation system CPX-AP in the software:

System structure

Network addressing

Address assignment of modules 

è

 Instruction manual for automation system CPX-AP

4. Transfer the automation project to the higher-order controller.

Behaviour of the display components of the module after error-free commissioning

[MD]

[SD]

[PL]

[MT]

green light

green light

green light

Off

Tab. 10 Behaviour of the display components after error-free commissioning

Assembly

9

Festo — CPX-AP-I-PB-M12 — 2020-03

Содержание CPX-AP-I-PB-M12































Отзывы: