background image

1

About this document

1.1

Other applicable documents

All available documents for the product 

è

 www.festo.com/sp.

Document

Contents

Instruction manual for automation system
CPX-AP

Instruction manual and important information on
assembly, electrical installation and maintenance
tasks as well as description of the automation
system CPX-AP

Tab. 1 Other applicable documents

1.2

Product version

This document refers to the following product versions:

Product

Version

CPX-AP-I-PB-M12

PROFIBUS interface CPX-AP-I-PB-M12 revision 1 or later

Tab. 2 Product version

The product version can be determined using the product label.

There may be an updated version of this document for these or later product versions

è

 www.festo.com/sp.

1.3

Product labelling

The product labelling is located on the right-hand side of the module. The Data Matrix code is on the
connection side. Scanning the printed Data Matrix Code with an appropriate device opens the Festo
Support Portal with the information appropriate for the product. Alternatively, the Product Key
(11-digit alphanumeric code on the product labelling) can be entered in the search field of the Support
Portal 

è

 www.festo.com/sp.

1.4

Specified standards

Version

IEC 60204-1:2016-10

EN 60204-1:2018-09

IEC 61158:2014-07

EN 60529:1991-10

Tab. 3 Standards specified in the document

About this document

Festo — CPX-AP-I-PB-M12 — 2020-03

4

Содержание CPX-AP-I-PB-M12































Отзывы: